EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-51-2GS8J5-18BSN

Description
Cable Assembly, 28AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-5-51-2GS8J5-18BSN Overview

Cable Assembly, 28AWG,

177-740-5-51-2GS8J5-18BSN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005107813
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D FEMALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.081 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors51
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.244 Ω
shieldYES
stay7X36
Wire gauge28 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Detailed introduction to embedded development
[b][color=#FF0000]Can anyone introduce me to embedded development? I am studying electronic communication and plan to do embedded development in the future. I don't know much about this aspect. I know...
雾海飘香 Embedded System
Has anyone used STM32's AD to collect the phase current feedback of the stepper motor to control the stepper motor's PWM wave duty cycle?
When the stepper motor is running at high speed, the current waveform is always bad. Has anyone used current sampling feedback to control the attenuation of the PWM wave to improve the current wavefor...
沈婷婷 Motor Drive Control(Motor Control)
I recently came into contact with MSP430, using F5229, and it was hard to learn. I don't know where to start
I recently came into contact with MSP430, using F5229. It was very difficult to learn. I don't know where to start. I haven't found any good information. I am a novice. I hope that some seniors can gi...
狼在工大 Microcontroller MCU
I can't understand the AD conversion code in FPGA. Thank you all.
I am a novice in FPGA. I bought a development board and followed the examples. Now I am studying AD conversion. However, I cannot understand the Verilog language. I need guidance from you seniors. I w...
ckwangwei FPGA/CPLD
Philips 107S7 strange malfunction
I have taken over a batch of monitors of this model, 6 of which have this fault, showing poor knife linearity and instability, sometimes normal, re-soldering N times is ineffective, replacing all capa...
绿草 Appliance Repair Collection
JLINK V8 usage issues
I just bought a JLINK V8 to debug the STM32 board. I can debug it in single step, but I can't simulate it in single step. Can someone familiar with it give me some advice? Thank you! Explanation: STM3...
arm.eew Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 179  1872  2780  2344  2746  4  38  56  48  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号