EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GA-02-3051-B

Description
Fixed Resistor, Thin Film, 0.25W, 3050ohm, 100V, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GA-02-3051-B Overview

Fixed Resistor, Thin Film, 0.25W, 3050ohm, 100V, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP

B0202GA-02-3051-B Parametric

Parameter NameAttribute value
Objectid1579386976
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance3050 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Amateur 30MHz wireless walkie-talkie
Software name: Amateur 30MHz wireless walkie-talkieLicense: SharewareSoftware Type: Design SolutionSoftware size: 411K...
fighting RF/Wirelessly
[Jihai APM32E103VET6S MINI development board review] Part 3: Timer PWM breathing light
[i=s]This post was last edited by ddllxxrr on 2022-9-14 20:19[/i]In the past, breathing lights were all programmed by hand. Now with CUBEMX, you can use it to set: Click the pin to be used as the brea...
ddllxxrr Domestic Chip Exchange
The MAX2395 output is matched to the SAW filter input for optimal cascaded gain flatness
The transmitter (TX) SAW filter output impedance is susceptible to the source impedance seen at the input. The impedance variation at the output port caused by the interaction of the MAX2395 with the ...
JasonYoo RF/Wirelessly
First-hand report: ADI Innovation Competition Award-winning works
Haha, I went to visit the ADI Innovation Design Competition Award Ceremony held in Central China in the afternoon, and I felt that the students were so cute.I will describe the plan in detail in an ar...
soso Electronics Design Contest
Wiring failed, error par:228
现在一个设计xc3s400,ise10.1,综合器为SynplifyERROR:$ar:228 - At least one timing constraint is impossible to meet because component delays alone exceed the constraint. A timing constraint summary below shows the...
eeleader FPGA/CPLD
About parts and finished electronic products
I've been soldering some DIY kits recently. After I soldered the kits, I found a problem... I want to ask for help from the experts to help me solve the problem... 1. What usually causes the output of...
overing1314 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2702  270  87  2522  552  55  6  2  51  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号