Resistor values are typically 120 to 240 ohms for 3.3V opera on and 82 to 120 ohms for 2.5V
opera on.
Figure 7 - Pull Up Pull Down Termina on
Resistor values are typically for 3.3V opera on
For 2.5V opera on, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous applica on notes on termina ng and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is op onal, depending on the applica on and the input logic requirements of
the next stage.
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
LVDS Applica on Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
+3.3V
OE or NC
10nF
1nF
1
6
10nF
OE or NC
2
5
100
3
4
10nF
OE or NC
2
5
Receiver
100
Receiver
3
4
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need addi onal components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
Regulations of the People's Republic of China on Radio Management (issued by the State Council and the Central Military Commission in September 1993) Chapter I General Provisions Article 1 These Reg...
I want to buy a sensor to collect pulse signals and connect the power circuit and amplification and filtering circuit. Can anyone recommend a cheap one to me?...
There are many types of sensors, which can be divided into different types according to different properties. Today, we will classify them according to the manufacturing process of sensors: Integrated...
The altera iv E series FPGA I use cannot be successfully configured in a low temperature environment. After powering on, there is no clock output from the DCLK pin. I measured the voltages and found n...
[i=s]This post was last edited by paulhyde on 2014-9-15 04:00[/i] The title seems to say that the car should move normally, but I don't know if the car can stop in the overtaking zone? When using PWM ...
Photovoltaic inverters are the core equipment of photovoltaic systems. Their main function is to convert the direct current generated by photovoltaic modules into alternating current that meets the...[Details]
On April 19, it was reported that Alibaba DAMO Academy is developing a neural network chip, Ali-
NPU
, which is mainly used for
AI
reasoning calculations such as image and video analys...[Details]
Recently, the results of the 2018 German Red Dot Design Award were announced. GoodWe, a company located in Suzhou High-tech Zone, stood out among thousands of outstanding design products from 5...[Details]
In the war without gunpowder between China and the United States,
ZTE
has become a new victim. The seven-year chip ban by the United States has pushed this communications giant to a life-or...[Details]
"Originally, there are many people who can design very good
chips
, but the market does not give domestic
chips
the opportunity to iterate, and domestic companies cannot give engine...[Details]
On April 20, the Photovoltaic Summit, guided by Jiangsu Renewable Energy Industry Association, hosted by Growatt, and supported by LONGi Solar Technology Co., Ltd. and Jiangsu Bigo New Energy Group...[Details]
The status of interrupts in developing embedded systems is absolutely unquestionable. In the era of C51 microcontrollers, there were only 5 interrupts, including 2 external interrupts, 2 timer/counte...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
1. Usage scenarios In the first case, when using a common STM32 delay function, similar to HAL_Delay(time), since this function uses a loop to judge and delay, when executing this function, the ent...[Details]
Recently, the "Smart Photovoltaic Industry Development Action Plan (2018-2020)" jointly issued by six departments has put this concept on the forefront. Photovoltaic smart solutions will become the ne...[Details]
China Energy Storage Network News:
The State Grid Corporation of China, this elephant, is planning to turn around and enter the emerging power service market.
The rallying cry for the tr...[Details]
When designing a product, if the application environment's requirements for power isolation are not considered, the product will be unstable due to improper design, and even high voltage may damage t...[Details]
In the Huaxing Optoelectronics LCD panel
factory
located in Guangming New District, Shenzhen
, apart from a few people repairing machines, it is often difficult to see other people. Here, ev...[Details]
This program is used in the development board to generate sounds of different frequencies. The overall program is relatively simple, mainly using two timers. The code and my comments are as follows. ...[Details]
China Energy Storage Network News:
On the 7th, Jurong Economic Development Zone signed a strategic cooperation framework agreement on comprehensive energy services with State Grid Jiangsu Int...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
