Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
-The gap between the capacity of China Mobile's GSM system and that of China Unicom's GSM system is gradually widening. -China Mobile's investment in GSM networks in 2005 will be about 8% lower than...
Micro Raw OS is released. It currently supports Cortex-M3 and 8051. It has very low resource utilization and does not lose real-time performance. Welcome to use it....
Is there any Vishay engineer in this forum? Can you let me know? I need a low temperature drift and high precision current sense resistor recently. Thank you! [[i] This post was last edited by youki12...
Questions: 1. As the title says. 2. If the serial port is disconnected only after the peripheral is powered off, is it hot-swappable? 3. Will the serial port be damaged if the serial port is disconnec...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
0 Introduction
Ultrasonic waves
are mechanical waves with a frequency of more than 20KHz, and the propagation speed in the air is about 340 m/s (at 20°C). Ultrasonic waves can be gene...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
Portable power applications are broad and varied. Products range from wireless sensor nodes with average power consumption of only a few microwatts to in-vehicle medical or data acquisition systems...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
Currently, high-frequency and high-efficiency DCDC converters are increasingly used in automotive electronic systems.
High switching frequency can use smaller power inductors and output filter...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
1 Introduction
With the development of computer technology and information technology in the world, the global information age has arrived. All countries are formulating their own development p...[Details]
1. Introduction
Stepper motor is a basic component that converts electrical energy into kinetic energy. It has been widely used in a variety of electromechanical equipment, such as various machine...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
