EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S271AG-0164CD8

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size729KB,17 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance  
Download Datasheet Parametric View All

8N4S271AG-0164CD8 Overview

LVDS Output Clock Oscillator

8N4S271AG-0164CD8 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1327869806
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TR
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
JESD-609 codee3
Installation featuresSURFACE MOUNT
Nominal operating frequency156.25 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry53/47 %
Terminal surfaceMatte Tin (Sn)
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S271
DATA SHEET
General Description
The IDT8N4S271 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Q
nQ
Pin Assignment
OSC
f
XTAL
2
÷P
÷N
DNU 1
OE 2
GND 3
6 V
DD
5 nQ
4 Q
÷MINT,
MFRAC
IDT8N4S271
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
25
Configuration Register (ROM)
OE
Pullup
7
IDT8N4S271CCD
JUNE 12, 2012
1
©2012 Integrated Device Technology, Inc.
LPC1500 Experience+ (ADC Routine)
Without further ado, let's get to the program int main(void) { uint32_t ucRegVal; char ucAdc_Str[60]; ADC_Config adc_Config; ADC_Config *pAdc_config = &adc_Config; SystemCoreClockUpdate(); GPIOInit();...
dj狂人 NXP MCU
What kind of packaging is used for Xilinx Virtex series chips?
As the title says, thank you ;P!...
zqzq501311 FPGA/CPLD
[GD32L233C-START Review] Part 2: Porting RTThread from Scratch
1. Introduction In preparation for the subsequent demo, we transplanted RTThread. Why not transplant FreeRTOS? Because domestic chips should use domestic systems! So let's get started! 2. Transplantat...
PowerWorld GD32 MCU
Changes in the stylus touch calibration process after changing the screen display orientation
I use a QQ2440V3 board with a 800*480 7-inch screen. I successfully changed the display to portrait mode by adjusting the display driver parameters. I observed that the pen touch calibration procedure...
stlong Embedded System
Which libraries are needed for functions like OpenStore...?
I want to write a small program for disk operation under evc, which needs to use functions such as OpenStore and OpenPartition. The definitions of these functions can be seen in the header file of the...
wbatjd Embedded System
PCB conversion to schematic
I am a beginner in protel and want to convert a PCB diagram into a schematic diagram. Is there any software to do this? There are a lot of copper wires on the PCB diagram, which looks very complicated...
ben007 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2575  2499  2840  2305  2061  52  51  58  47  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号