Bi-directional pin. Upon power-on, the value of VDD_SEL is latched in and used to
select the power (see Power Selection table 2 ). Internal pull down defaults SST1 to 0,
use external pull-up to set to 1. After power-up this pin acts as 12MHz output clock.
Bi-directional and Tri-level pin. Upon power-on, the value of SEL10_8 is latched in and
used to select the output frequency (See frequency selection table 3 ). Tri level input: M
= Do not connect, 1 = Pull up, 0 = Pull down. After power-up this pin acts as 10MHz
clock, 8MHz clock, or “No output”, depending on SEL10_8.
Ground connection.
Bi-directional pin. Upon power-on, the value of XTAL_SEL is latched in and used to set
the input crystal frequency (24.575MHz or 14.31818MHz). Set XTAL_SEL to 0 (default)
for 24.576MHz input crystal, set XTAL_SEL to 1 for 14.31818MHz input crystal (see
Crystal Selection Table on page 1). . After power-up this pin acts as 27MHz output
(with 24.576MHz crystal) or as 14.31818MHz pass through clock (with 14.31818MHz
crystal), depending on the input crystal.
The 27MHz output can be modulated for low EMI using Spread Spectrum.
3.3V power supply for 27MHz, 10MHz, 12MHz, and 24.576MHz.
24.576MHz/SST1
VDDB1
VDD25M
25MHzx2
VSS25M
12MHz/VDD_SEL
7
8
9
10
11
12
B
P
P
O
P
B
10_8MHz/SEL10_8
VSSB2
13
14
B
P
27_14.318MHz/XTAL_SEL
15
B
VDDB2
16
P
FUNCTIONAL DESCRIPTION
Tri-level and two-level inputs
In order to reduce pin usage, the PLL702-02 uses tri-level input pins. These pins allow 3 levels for input selection: namely, 0 =
Connect to GND, 1 = Connect to VDD, M = Do not connect. Thus, unlike the two-level selection pins, the tri-level input pins are
in the “M” (mid) state when not connected. In order to connect a tri-level pin to a logical “zero”, the pin must be connected to
GND. Likewise, in order to connect to a logical “one”, the pin must be connected to VDD.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 08/30/05 Page 3
PLL702-02
Low EMI Peripheral Clock Generator for Notebook & Motherboards
Connecting a bi-directional pin
The PLL702-02 also uses bi-directional pins. The same pin serves as input upon power-up, and as output as soon as the inputs
have been latched. The value of the input is latched-in upon power-up. Depending on the pin (see pin description), the input can
be tri-level or a standard two-level. Unlike unidirectional pins, bi-directional pins cannot be connected directly to GND or VDD in
order to set the input to "0" or "1", since the pin also needs to serve as output. In the case of two level input pins, an internal pull-
up resistor is present. This allows a default value to be set when no external pull down resistor is connected between the pin
and GND (by definition, a tri-level input has a the default value of "M" (mid) if it is not connected). In order to connect a bi-
directional pin to a non-default value, the input must be connected to GND or VDD through an external pull-down/pull-up
resistor.
Note:
when the output load presents a low impedance in comparison to the internal pull-up resistor, the internal pull-up resistor
may not be sufficient to pull the input up to a logical “one”, and an external pull-up resistor may be required.
For bi-directional inputs, the external loading resistor between the pin and GND has to be sufficiently small (compared to the
internal pull-up resistor) so that the pin voltage be pulled below 0.8V (logical “zero”). In order to avoid loading effects when the
pin serves as output, the value of the external pull-down resistor should however be kept as large as possible. In general, it is
recommended to use an external resistor of around one sixth to one quarter of the internal pull-up resistor (see Application
Diagram).
Note:
when the output is used to drive a load presenting an small resistance between the output pin and VDD, this resistance is
in essence connected in parallel to the internal pull-up resistor. In such a case, the external pull-down resistor may have to be
dimensioned smaller to guarantee that the pin voltage will be low enough achieve the desired logical “zero”. This is particularly
true when driving 74FXX TTL components.
APPLICATION DIAGRAM: BI-DIRECTIONAL PINS WITH INTERNAL PULL-UP
Internal to chip
VDD
External Circuitry
R
up
Power Up
Reset
R
RB
Output
EN
Bi-directional pin
Clock Load
Latched
Input
Latch
R
UP
/
4
Jumper options
NOTE:
Rup=Internal pull-up resistor (see pin description). Power-up Reset : R starts from 1 to 0 while RB starts from 0 to 1.
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 08/30/05 Page 4
PLL702-02
Low EMI Peripheral Clock Generator for Notebook & Motherboards
Electrical Specifications
1. Absolute Maximum Ratings
PARAMETERS
Supply Voltage
Input Voltage, dc
Output Voltage, dc
Storage Temperature
Ambient Operating Temperature*
Junction Temperature
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
SYMBOL
V
DD
V
I
V
O
T
S
T
A
T
J
MIN.
-0.5
-0.5
-65
-40
MAX.
4.6
V
DD
+0.5
V
DD
+0.5
150
85
125
260
2
UNITS
V
V
V
°C
°C
°C
°C
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product
reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this
specification is not implied.
*
Note:
Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
2. AC Specifications
PARAMETERS
Input Frequency (to be set via XTAL_SEL)
Output Rise Time
Output Fall Time
Duty Cycle
Duty Cycle 8MHz clock
Max. Absolute Period Jitter
Max. Jitter, cycle to cycle
CONDITIONS
+/- 20ppm accuracy
0.8V to 2.0V with no load
2.0V to 0.8V with no load
At VDD/2
At VDD/2
Long term, No SST
Long term + Short term
MIN.
TYP.
14.31818
24.576
MAX.
UNITS
MHz
MHz
1.5
1.5
45
43
50
50
55
57
150
120
ns
ns
%
%
ps
ps
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
Hello everyone, I am a junior who has just learned 51. Recently, I have made something similar to a competition stopwatch. Now I have encountered some problems and would like to ask for help. Use time...
Using a 4.7k resistor to pull down boot0, the voltage measured by a multimeter is 1.0v, and boot1 is also pulled down by 4.7k, the voltage is 0V.Replacing boot0's 4.7k with 1k has basically no change ...
I am a beginner. For beginners, I will briefly talk about the three points about FPGA program configuration that we are most concerned about and must understand. 1. Where is the FPGA program stored? L...
How to set the system to perform corresponding actions when there is no operation for a certain period of time? My system includes buttons and touch screen. I searched for a similar question on the In...
Hello everyone, I'm new here!!
I have a question for everyone.
About the calibration problem of LSM6DS3! ! For example, adxl343 only needs to set the offset register, but LSM6DS3 does not work even if...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Electric bicycles have long been a means of transportation for lower-income groups due to their affordability. The largest concentrated expense in the use of electric vehicles is the cost of replac...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
