There is a balancing seesaw. An automatically movable object is placed on the seesaw. An angle sensor is placed on the object. The angle sensor is used to measure the tilt angle of the seesaw during t...
Although I have been learning computers for two years, I still don’t know exactly what they are used for! Because I have been writing topics from books, and I haven’t developed any actual software yet...
I've known about this little sister of the Lin family for a long time. I've read her ghost stories and watched her Christmas pole dance. They were all quite shocking. Who would have thought that there...
[url=https://bbs.eeworld.com.cn/thread-435349-1-1.html]You answer questions, I give gifts [TI Technology Forum] - First Issue[/url] Thank you for your support and participation in the event. I hope th...
In the past few days, the news that ZTE was "banned" by the US Department of Commerce has triggered widespread reflection and concern in various domestic industries about the lack of independent co...[Details]
The update interrupt initialization configuration of the stm32 advanced timer TIM1 is not much different from that of the ordinary timer. What needs to be paid attention to is the configuration of TI...[Details]
When Amazon launched its first
cloud computing
service, the outside world was not optimistic about this direction, as it had high investment, low profits and many uncertainties. Let's follo...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
The goal of this article is to build a TCP client based on the previous project that can ping the PC, and can actively send data to the PC, and can also send and receive data with the PC, and display...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
This is my first time writing an STM32 program. I have many questions to ask. I want to convert the data of the SO of MAX6675 into the actual temperature and read it out using the serial port tool. I...[Details]
The article is written for LPC2148, but it is also applicable to Samsung's 44B0 chip. You only need to select S3C44B0 as the corresponding CPU when selecting it. JLINK debugging experience un...[Details]
1. Heart rate measurement principle 1. What is a heart rate module? The heart rate module is professionally used to monitor the heart rate of the wrist, fingers, forehead, earlobe, chest and other ...[Details]
Household photovoltaic power stations mainly utilize idle resources on existing household buildings, such as roofs, wall facades, balconies, courtyards, etc., to install and use distributed photovo...[Details]
LiDAR: Autonomous driving from the perspective of optoelectronic technology LiDAR and competing sensor technologies (camera, radar, and ultrasonic) intensify the need for sensor fusion and the need...[Details]
ADI has established long-term good relationships with car manufacturers and Tier 1 component suppliers. Based on its previous long-term successful cooperation with new energy vehicles and suppliers a...[Details]
How to convert the pin voltage value into V using the built-in ADC of STM32? V(ADC) = Value(ADC) * V(ref)/4096 (The ADC of STM32 is 12 bits, so the maximum value of the AD word is 4096)
Where V(ADC...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
