EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLAFC2722

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-FLAFC2722 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-FLAFC2722 Parametric

Parameter NameAttribute value
Objectid4000985499
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1531 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
atmel AVr cv compiler software (embedded c programming and atmel avr)
The software used is the atmel avr microcontroller and the cv compiler...
463854329 Microchip MCU
I beg you to answer my confusion: the relationship between embedded systems and software engineering
I studied software engineering in college. Now I am a junior and I have just learned something about software. I had no direction before. I was preparing for the postgraduate entrance examination befo...
leafky Embedded System
Development board made by microcontroller enthusiasts, updated every day
Without further ado, here are some renderings: Whole board:12232F with screen:Overall schematic:Below are the sub-schematics:...
myemcu 51mcu
Should I go for computer training? I'm confused.
I am a girl and want to attend the training for big computers, but I don't know whether I should attend or not. I am very confused and there are many different opinions. I really don't know what to do...
tigerweihui Embedded System
Development process of eCAN in DSP28335
I used the CAN bus of DSP28335 for some time. In fact, I have almost understood the basic principles of CAN bus, but there are still some problems in the process of configuring 28335. 1. About TI rout...
Aguilera DSP and ARM Processors
How to improve FPGA design efficiency?
Asking an expert for advice: I always feel that the efficiency of FPGA and CPLD design is low. Is there any good way to improve the efficiency?...
eeleader FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 852  2270  1019  687  2777  18  46  21  14  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号