EEWORLDEEWORLDEEWORLD

Part Number

Search

177-710-2-67S8K7-18RAN

Description
D Microminiature Connector, 67 Contact(s), Female, Receptacle,
CategoryThe connector    The connector   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-710-2-67S8K7-18RAN Overview

D Microminiature Connector, 67 Contact(s), Female, Receptacle,

177-710-2-67S8K7-18RAN Parametric

Parameter NameAttribute value
Objectid7004411902
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresSTANDARD: MIL-DTL-83513
Body/casing typeRECEPTACLE
Connector typeD MICROMINIATURE CONNECTOR
Contact point genderFEMALE
DIN complianceNO
empty shellNO
Filter functionNO
IEC complianceNO
insulator materialLIQUID CRYSTAL POLYMER/POLYPHENYLENE SULFIDE
MIL complianceYES
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeCABLE AND PANEL
OptionsGENERAL PURPOSE
Shell surfaceNICKEL
Shell materialALUMINUM ALLOY
Total number of contacts67
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Analysis of the front-end circuit of push-pull amplifier
See the picture. This is the front end of the push-pull amplifier. Points a and b are connected to the next level. Please solve the voltage of a and b. If the AC signal is a small signal, it can be an...
wh40062 Analog electronics
Why does Workbench3.0 show "failed to connect to the wind river registry on host" every time it starts?
And there is a red cross on the default (localhost) in the lower left corner. Tornado has been uninstalled but it still doesn't work. There is no Tornado registry in the service. Every time I start it...
cdqd Embedded System
Actel to begin shipping FPGA samples with mixed analog circuits and flash memory
[;)][;)][;)]  Actel Inc. of the United States recently announced the first four products of its FPGA series "Fusion" that mixes analog circuits and flash memory, and will start shipping samples of one...
fighting Analog electronics
How to change the component package in PCB?
Experts, the capacitor package in the picture is a bit big, how can I change it to a smaller package? Thank you very much...
huohuiqing PCB Design
Addressing, how to get the value in external ROM through RO/R1
The sample code is as follows: ORG 0000H LJMP MAIN ORG 0100H MAIN: MOV 50H,#16H; Set RAM, data at position 0x50 MOV 51H,#17H MOV R0,#50H; Set the starting position of indirect addressing MOV A,@R0; Ge...
xrg0228 Embedded System
The company's PC can be customized in this way, BH is right
I can't refuse to admit my age! Before, I only knew that the NB I used could be customized according to my own needs, but I didn't expect that the company's commercial desktop computer could be so NB~...
李晨吧外交 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1295  2644  2926  1995  1276  27  54  59  41  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号