EEWORLDEEWORLDEEWORLD

Part Number

Search

177-710-2-69CS6J7-18FDN

Description
Cable Assembly, 26AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-710-2-69CS6J7-18FDN Overview

Cable Assembly, 26AWG,

177-710-2-69CS6J7-18FDN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7004907551
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.23
Other featuresSTANDARD: MIL-DTL-83513
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.129 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors69
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.147 Ω
shieldNO
stay19X38
Wire gauge26 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Teacher, I want to ask you a question
I use T0 to receive pulses, T1 to time 50ms (the natural frequency of the crystal oscillator is 11.0592MHZ), and finally I give the high eight bits and low eight bits of T0 to A and B respectively. So...
15075018luerdu MCU
msp430f149 microcontroller serial port C program
Introduction to msp430f149 microcontroller: MSP430 series microcontroller is a 16-bit ultra-low power mixed signal processor (Mixed Signal Processor) with a reduced instruction set (RISC) that was lau...
fish001 Microcontroller MCU
About the problem of LPM_ROM in Modelsim simulation of Altera
Regarding the problem of LPM_ROM in Modelsim simulation of Altera, when doing functional simulation, the following error is always prompted: # ** Error: (vsim-7) Failed to open VHDL file "my_rom.hex" ...
eeleader-mcu FPGA/CPLD
Data coverage problem under wince
When I use the development board to connect to the instrument via the serial port, I can continuously receive data, but the later data cannot overwrite the previous data. How can I make the later data...
sangxh7 Embedded System
Please tell me about the backlight adjustment under CE
Dear bosses: After entering the CE system, right-click on the desktop (or long press on the touch screen), the display properties will appear. The second item of the display properties is "Backlight"....
anzx23 Embedded System
【3】 DIY sharing of Bluetooth remote control balancing car
[i=s]This post was last edited by lb8820265 on 2015-10-4 20:17[/i] [align=left][font=宋体] [size=3]This post is for the DIY[font=宋体] sharing event on September 10. It just so happens that a part of the ...
lb8820265 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2664  1523  2793  2368  1787  54  31  57  48  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号