177-710-2-69CS6K7-18LDN datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-710-2-69CS6K7-18LDN

177-710-2-69CS6K7-18LDN: DescriptionCable Assembly, 26AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-710-2-69CS6K7-18LDN Overview

Cable Assembly, 26AWG,

177-710-2-69CS6K7-18LDN Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	7004907771
Reach Compliance Code	compliant
Country Of Origin	USA
YTEOL	8.23
Other features	STANDARD: MIL-DTL-83513
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	MICRO-D MALE
ConnectorSide2	MICRO-D FEMALE
Connector bracket type	CABLE ASSEMBLY
structure	STRANDED
Cross-sectional area	0.129 mm2
DIN compliance	NO
IEC compliance	NO
insulator material	POLYTETRAFLUOROETHYLENE
Jacket material	ETHYLENE-CHLOROTRIFLUOROETHYLENE
length	0.467 mm
MIL compliance	YES
Number of conductors	69
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Rated current	3 A
Rated voltage	150 V
resistance	0.125 Ω
shield	NO
stay	19X38
Wire gauge	26 AWG
Wire and Cable Names	FLEXIBLE CORD AND FIXTURE WIRE

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

Four-way infrared receiving control circuit

Deep well water pump motor protection circuit

BL0509/BL0510 circuit block diagram

Carrier transmitting circuit of cable broadcast disconnection monitor

MP3 circuit diagram_torque solution 3

555 multi-function infrared remote control circuit

Design of communication system baseband verification platform based on FPGA: Design of FPGA-based communication system baseband verification platform pdf paper....; liwenqi FPGA/CPLD

SDRAM read and write test in EBOOT: Heroes: My system is based on pxa255+wce4.2, with two banks of sdram, each bank is connected to 64M, and consists of two 32M chips. In eboot, to test sdram, I read and write the addresses of the two b...; shangyl Embedded System

Simple circuit and powerful performance ECG acquisition circuit: [i=s]This post was last edited by Mandy on 2015-2-11 09:46[/i] This human ECG signal acquisition circuit was DIYed by me when I first started to use analog circuits. I used TI's solution and samples f...; Mandy Analogue and Mixed Signal

TRACE32 Model LA-7708 for sale at low price: Low price transfer TRACE32 model LA-7708 Price 20,000, accept small knife, if you need it, contact: 13713676870...; wu1239 Embedded System

Selling a Digilent Basys3 FPGA development board: [size=14px]I am studying in the United States, and I bought a Basys3 FPGA development board for study. But since I am not a major FPGA developer, the board is idle and I plan to sell it. The board is ...; masonmvp Buy&Sell

In AD, the ID changes always occur when the schematic is imported into the PCB: I drew the PCB board with AD and established a project. There are schematics and corresponding PCB boards in the project. The schematics can be fully used after being imported into the PCB. Everything...; 工控小学徒 PCB Design

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components