177-740-2-69CS6J1-18LNN datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-740-2-69CS6J1-18LNN

177-740-2-69CS6J1-18LNN: DescriptionCable Assembly, 26AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-740-2-69CS6J1-18LNN Overview

Cable Assembly, 26AWG,

177-740-2-69CS6J1-18LNN Parametric

Parameter Name	Attribute value
Objectid	7005065342
Reach Compliance Code	unknown
YTEOL	8.23
Other features	STANDARD: MIL-DTL-83513
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	MICRO-D MALE
ConnectorSide2	MICRO-D FEMALE
Connector bracket type	CABLE ASSEMBLY
structure	STRANDED
Cross-sectional area	0.129 mm2
DIN compliance	NO
IEC compliance	NO
insulator material	CROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length	0.467 mm
MIL compliance	YES
Number of conductors	69
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Rated current	3 A
Rated voltage	150 V
resistance	0.147 Ω
shield	NO
stay	19X38
Wire gauge	26 AWG
Wire and Cable Names	FLEXIBLE CORD AND FIXTURE WIRE

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

The accuracy of DC-DC power supply is becoming more and more precise with the accuracy of FPGA.

STK4311II audio IC circuit diagram

The most practical basic diagram circuit 39 - motor intermittent cycle start and stop control circuit

LR3709 (video recorder) infrared remote control transmitter circuit

The circuit of the peak chicken device to replace the picture light

50～500kHz crystal oscillator

Conductivity unit conversion: Siemens is a unit of conductance, susceptance and admittance in physical circuits and the International System of Units. The symbol of Siemens is S, and its Chinese abbreviation is [西]. The full Engli...; wljmm Analog electronics

At home,: ARM learning materials...; zouxiaoping1012 FPGA/CPLD

Read the .tsv file recording sensor data through labview: [i=s]This post was last edited by suoma on 2017-4-1 18:18[/i] Continuing from the previous post [url=https://bbs.eeworld.com.cn/thread-524954-1-1.html]https://bbs.eeworld.com.cn/thread-524954-1-1.html...; suoma MEMS sensors

How to develop GPS and what equipment is needed? How to choose GPS module and MCU: I am studying GPS devices recently, but I don't know what kind of development board I need to develop GPS. How to choose GPS module and MCU? Are there any standards? Can anyone with development experi...; wangxuguang150 Embedded System

Why does the transceiver use a bitslip module at the receiving end and how to implement it?: RT. The altlvds_tx and altlvds_rx cores are used. After the serial-to-parallel conversion at the receiving end, a bitslip module is used. It seems to have completed a bit shift function. I don't quite...; robertslyh FPGA/CPLD

Please help: I just registered and don’t know how to get this chip coin, eh!...; xzhxcf PCB Design

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components