EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-2-69CS8J1-18LWN

Description
Cable Assembly, 28AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-740-2-69CS8J1-18LWN Overview

Cable Assembly, 28AWG,

177-740-2-69CS8J1-18LWN Parametric

Parameter NameAttribute value
Objectid7005065626
Reach Compliance Codeunknown
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.081 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors69
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.244 Ω
shieldYES
stay7X36
Wire gauge28 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
【ESP32 Learning】Download ESP32 LoBo firmware
[size=14px]ESP32 Lobo version is another branch of MicroPython. It appeared because the official progress was too slow, so loboris wrote the ESP32 Lobo branch himself and opened a forum to discuss Mic...
dcexpert MicroPython Open Source section
Understand the role and use of capacitors in one article
Capacitors are the most common and commonly used devices in circuit design. They are one of the passive components. Active devices are simply devices that require energy (electricity) power, and devic...
btty038 Energy Infrastructure?
Very practical free tool - a must for engineers! Chip query, pdf download software!
Software Operation Instructions:1. This software is pure green software, no need to install, just unzip and use directly.2. Set the PDF save address. Save Path is the save address. The default is on t...
281854691 TI Technology Forum
【I want to contribute】EDK principle tools and skills guide
This tutorial describes the steps to create and test a hardware processor system design using the Embedded Development Kit (EDK). The system requirements for this tutorial are as follows: Xilinx Spart...
GONGHCU FPGA/CPLD
Today I used Launchpad's ADC10 to collect the on-chip temperature and displayed it in 12864.
I have only posted part of this program. As for the 12864 serial display module, please read my previous post. The complete program can realize temperature measurement. However, I still don’t understa...
ice0107 Microcontroller MCU
The results of the GD32F350 contest (sharing experience & interaction) are as follows: Thanks to all the cool people in the contest
{:1_123:}The results of the competition are out and will be announced later today. To warm up, let's first reveal the enthusiastic netizens in the competition. This competition adopts a scoring system...
nmg GD32 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1421  667  1119  970  1645  29  14  23  20  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号