EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-67CS0J5-18PVN

Description
Cable Assembly, 30AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-740-5-67CS0J5-18PVN Overview

Cable Assembly, 30AWG,

177-740-5-67CS0J5-18PVN Parametric

Parameter NameAttribute value
Objectid7005112055
Reach Compliance Codeunknown
YTEOL9.35
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.051 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.385 Ω
shieldYES
stay7X38
Wire gauge30 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
LPM_RAM_DQ
Today I will study LPM_RAM_DQ. My platform is quartus 7.2 and modelsim 6.5a. My device is the famous cyclone EP1C6Q240C8. My quartus graphic file is [img]C:\Documents and Settings\Tony\Desktop\1_JPG_t...
amw196209 Embedded System
nRF24L01 Debugging Challenges
Transmitter: No ACK, no retransmission, it loops by itself. Status: FIFO_STATUS 0x11 TX_EMPTY + RX_EMPTY STATUS 0x0E RX_FIFO_EMPTY What if TX_DS is missing? No matter what, it is considered that FIFO_...
cl17726 RF/Wirelessly
Problems with using SSD1926
I just took over the development of SSD1926 LCD controller and encountered some problems. Please help! I use 16-bit 8080 interface. After RESET, I can read the four registers starting from address 00H...
llmdd Embedded System
GNU_ARM series: routines and makefile comment understanding version that can be used for STM32F3 Discovery
[i=s]This post was last edited by Xin Xin on 2014-12-6 01:55[/i] In the evening, I looked at LibOpenCm3, which I had high hopes for. Unexpectedly, it could not even compile. And what I found was that ...
辛昕 Programming Basics
ML2724 RF CLK frequency tolerence range
Who can tell me the acceptance range of RF-CLK frequency of ML2724? Thank!...
jxyang730 RF/Wirelessly
Who will use CS42L52?
There is a CS42L52 on the development board. The board is not equipped with the development program of this chip. I wrote it myself. I2C can access the chip normally, but there is no sound when I2S se...
0nline MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1016  1822  822  2391  1356  21  37  17  49  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号