EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-67GP0J1-18BZG

Description
Cable Assembly, 30AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-5-67GP0J1-18BZG Overview

Cable Assembly, 30AWG,

177-740-5-67GP0J1-18BZG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005112937
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL9.35
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D MALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.051 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.466 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.385 Ω
shieldYES
stay7X38
Wire gauge30 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com

Recommended Resources

Can tantalum capacitors replace aluminum electrolytic capacitors?
As shown in the circuit diagram, the electrolytic capacitors C13, C11, C15, and C16 in the power supply part were all tantalum capacitors at the beginning. There is a very strange phenomenon, that is,...
赵怡彬 Power technology
Can't generate .cod file after setting environment variable WINCECOD?
I have set the environment variables in the BAT configuration file: set WINCEMAP=1 set WINCECOD=1 After compilation, the corresponding .map and .cod files should be generated. However, the .map file c...
rong81117 Embedded System
evc serial port programming serial port debugging tool ask the expert
I am writing an evc serial port program for serial communication between arm and dsp. But I have encountered a problem in writing and debugging. This is the serial port receiving thread in the program...
mfxbb Embedded System
[Trf7960 question] How to modulate the 13.56M antenna to match 50Ohm?
I use TRF7960 to read and write M1 cards. The circuit part refers to the evaluation board of Lm3s9b96. The antenna part on my board has output 13.56M sine wave. Now I can read and write registers (0x0...
h0nly_zhang Microcontroller MCU
Newbie, ask about ARM's B instruction
In the assembly language, there is BL FUN and then there is a B. What does this "B." do? I have read several books on ARM instructions but none of them explain it clearly. Please give me some advice. ...
gaojunqian ARM Technology
Looking for entrepreneurial partners in the industrial control industry (only in Shenzhen)
Our company is engaged in wireless communication. We have a formal office building of more than 90 square meters in Luohu District. It is located in the center of the city with convenient transportati...
qiujinlin369 Embedded System

Popular Articles

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1412  1182  1966  497  285  29  24  40  10  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号