FPDR1C1261B02XX datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> FPDR1C1261B02XX

FPDR1C1261B02XX: DescriptionSpecial Switch,; CategoryMechanical and electronic products switch; File Size251KB，5 Pages; ManufacturerAPEM; Environmental Compliance

Download Datasheet Parametric View All

FPDR1C1261B02XX Overview

Special Switch,

FPDR1C1261B02XX Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145007563830
Reach Compliance Code	unknown
ECCN code	EAR99

Preview

Download Datasheet

View All

New!

Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching

Distinctive features and specifications

4.50

(.177)

Ø26.50

(1.043DIA)

FP series

00 )

4. IA

Ø3 39D

Full actuator or symbol illumination

26.50

(1.043)

Suited for integrated designs

Large but lightweight

Pad printed or laser etched symbols

Snap-in and threaded bushing models

Pad printing

Laser

0.50

(.020)

6.30

(.248)

2.80

(.110)

Ø29.80

(1.173)

Non-illuminated

Ø26.50

(1.043DIA)

00 )

4. IA

Ø3 39D

26.50

(1.043)

Illuminated

4.50

(.177)

6.30

(.248)

ELECTRICAL SPECIFICATIONS

0.50

(.020)

MATERIALS

Ø30.00x1.50 SI

2.80

(.110)

• Max. current/voltage rating with resistive load :

- silver contacts (code 2) : 4A 12VDC

- gold plated contacts (code 4) : 200mA 12VDC

• Initial contact resistance : 50 mΩ max.

• Insulation resistance : 1 GΩ min. at 500VDC

• Dielectric strength : 1.000 Vrms 50 Hz min.

• Electrical life at full load :

- Momentary models : 1 million cycles (gold plated contacts)

400.000 cycles (silver contacts)

- Latching models : 200.000 cycles

GENERAL SPECIFICATIONS

(1.181DIAx1.50 IS)

• Case : PA46

• Actuator : PA12, gloss finish

• Bushing/ bezel : ABS, gloss finish

• Contacts :

Silver (code 2)

or silver, gold plated (code 4)

WIRING DIAGRAM

POLE 2

LED

• Panel thickness :

- Snap-in version : 1,5 (.059) to 2 mm (.078) with panel gasket

2 (.078) to 2,5 mm (.885) without panel gasket

- Threaded bushing version : 1(.039) to 9 mm (.354) max.

• Total travel : 2,8 mm

± 0,5 mm

• Typical operating force : 8N

± 2N

• Low level or mechanical life :

- Momentary models : 1 million cycles

- Latching models : 200.000 cycles

• Torque : 2 Nm max. applied to nut

• Operating temperature : -40°C to +75°C

LED

POLE 1

The company reserves the right to change specifications without notice.

B2-150

www.apem.com

APEM

Recommended Resources

Demagnetization circuit of electromagnetic chuck of MM7120 surface grinder

Simple light control switch circuit

High Performance Digitally Controlled Amplifier-Gain Divider

Phototransistor pulse input circuit

555 darkroom exposure switch timer circuit

555 pyroelectric infrared sensing and light control delay power-saving socket circuit

I need help with questions about the effect of insulation type on the final value when calculating electrical clearance.: According to GB4943, when calculating the electrical clearance and creepage distance between conductors, the insulation type needs to be considered. According to the standard, the clearance requiremen...; 安圣基 PCB Design

[CH246 & CH241 Wireless Charging Kit Evaluation] Part 5 - Battery Charging Experiment with Wireless Charging: Use Qinheng's wireless charging transceiver kit and a charging circuit board to charge the battery. The measured battery charging current is 200mA....; oxygen_sh Power technology

First acquaintance with Qinheng CH246 & CH241: Because of the epidemic, I received it after the Spring Festival, and then I found that the voltage could not be measured on the CH241K evaluation board (I suspected that the coil was broken). Thanks ...; tobot Power technology

Infineon Motor Kit EVAL-IMOTION2GO Study Notes 5: [i=s]This post was last edited by my student number on 2023-2-20 00:31[/i]The previous note introduced the UART mode and software programming of T038, but when I was ready to start, I found a problem:...; 我的学号 Motor Drive Control（Motor Control）

[Xianji HPM6750EVK2 Review] 2. OpenHarmony compilation and burning experience: [i=s]This post was last edited by dql2016 on 2023-2-19 19:21[/i]Development environment construction https://device.harmonyos.com/cn/docs/documentation/guide/ide-install-windows-ubuntu-000000119407374...; dql2016 Domestic Chip Exchange

The floating ground is isolated by a transformer. Is it suitable to use a high-voltage capacitor 1nF to bridge it?: 1. If the working ground GGND and the interface ground EGND in the system are both floating, when using an Ethernet port transformer, should a C12 high-voltage capacitor (1nF) be connected in parallel...; 安圣基 PCB Design

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components