EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AA-02-3052-D

Description
Fixed Resistor, Thin Film, 0.25W, 30500ohm, 100V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AA-02-3052-D Overview

Fixed Resistor, Thin Film, 0.25W, 30500ohm, 100V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP

B0202AA-02-3052-D Parametric

Parameter NameAttribute value
Objectid1579349084
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance30500 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
I would like to ask about the GPRS module communication question
I want to use ARM to do a wireless communication project, but I don't know some ideas. I connect a GPRS module (such as Siemens MC55) to the serial port of my ARM board, and a camera to the USB port o...
mz_flying Embedded System
Doesn't Windows use int13 to operate the disk?
Please advise, since Windows does not operate the disk through int13, then the working principles of the current hard disk recovery cards should not be as described below: Analysis of the working prin...
zjhzlswxh Embedded System
VS 2005 compiles tcpmp 0.72 in common and module machine type 'THUMB' conflicts with target
When I set up my own SDK, this error occurred: module machine type 'THUMB' conflicts with target machine type 'ARM'. It is fine when using PPC 2003. What's going on?...
wj54321 Embedded System
Multi-clock design strategy for FPGA in large-scale designs
When implementing large designs with FPGAs, you may need the FPGA to have multiple data paths running with multiple clocks. This type of multi-clock FPGA design must be designed with special care, and...
呱呱 FPGA/CPLD
Help: JTAG debugging is fine, but downloading to the target board does not run correctly
I made a data acquisition program using F149, downloaded it to the target board using JTAG, and it ran correctly after debugging. After exiting debugging, I unplugged the JTAG connection and let the t...
flywing Microcontroller MCU
Power chip replacement
What should be considered when changing the power chip of the circuit board?...
zhonghuadianzie PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 211  1715  1506  1487  2844  5  35  31  30  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号