1. What is a base station? What does a base station consist of?The radio access network, also known as RAN (Radio Access Network). Simply put, it is the network that connects all mobile terminals to t...
The explosive development of wireless technology has spawned a variety of industrial, scientific and medical (ISM) band wireless standards. Thanks to these new standards, various wireless applications...
Hibernation moduleThe Hibernation module provides a means of reducing power consumption by managing the removal and restoration of power. When the processor and peripherals are idle, power can be comp...
[b]Special topic motivation[/b] Some scholars believe that Guangdong is facing many major problems that need to be solved in the process of modern industrial upgrading, among which the most prominent ...
I was bored, so I thought about this question! I am not referring to the common RC reset and pulse reset. I want to know the internal situation of the microcontroller. After receiving the reset pulse,...
[i=s]This post was last edited by lbbook on 2020-1-1 14:03[/i]Series of posts:
1. AWR1843BOOST unboxing
2. Use of AWR1843BOOST
3. AWR1843BOOST corridor ranging value test environment
4. AWR1843BOOST c...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
The Challenge:
Improving Siemens Wind
Turbine Controls
System software automated testing for regular releases, validating wind turbine control system components during the developme...[Details]
0 Introduction
In microwave, radar, radio and television, and communication systems, the problem of coupling RF power is often encountered. A directional coupler is a directional power divide...[Details]
3. Driving circuit design
The power driver uses a field effect tube, which is a field-controlled device with a capacitance effect between the gate and source, so it has high requirements for t...[Details]
When programming in C and assembly, there are interface issues between variables and functions in C and assembly.
Variables defined in a C program are put into the .bss area after being compile...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
