I wanted to make the attachment free, but in order to reduce irresponsible downloading and promote forum efficiency, the attachment is sold for 1 core coin. I hope everyone will understand. Friends wh...
When tracking the wince serial port driver, a cxx0017 error appears in the watch window. Some variables cannot be found, and the prompt "symbol "pSerialHead" not found" is displayed. Several other var...
[b][color=#75db3][url=http://www.cnblogs.com/zhixingwujiang/archive/2011/07/25/2116650.html]A Preliminary Study on the Android Boot Process[/url][/color][/b] [color=rgb(0, 0, 0)][backcolor=rgb(254, 25...
Comparison of three basic amplifier circuits1. The input impedance and output impedance range from tens of ohms to hundreds of kiloohms. What causes this? How to select the application based on the in...
There are relatively few book resources now, I hope you can give me some advice, thank you, for example, how to make the open and exit functions under the file menu and display them on the smartphone ...
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
Superconductors have physical properties such as zero resistance effect, Meissner effect and Josephson effect, which make them have broad application prospects and unparalleled advantages in many b...[Details]
If you do not use an external crystal on the STM32, the connection method of OSC_IN and OSC_OUT If you use the internal RC oscillator instead of an external crystal, please follow the following metho...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
The single-chip microcomputer running light program requires all 32 serial ports to be used, and each serial port has eight LEDs. Question supplement: The 8051 single-chip microcomputer is used, an...[Details]
Manually assemble the following program machine code and analyze the execution function of the program segment. CLR A MOV R2, A MOV R7, #4 LOOP: CLR C MOV A, R0 RLC...[Details]
A simple experimental programming question for the microcontroller: write a 3-byte binary addition subroutine. The program entry is: addend 1: 22H, 21H, 20H three bytes, 22H is the highest bit; adden...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
It is required to use timer/counter 1 for timing, with a timing of 1 second; timer/counter 0 for counter, and the external pulse to be counted is connected from P3.4 (T0). The microcontroller will co...[Details]
Requirements: Set timer T1 as an external event counter, count 500 pulses every time, then switch T1 to timing mode and output a positive pulse with a width of 10ms at P1.2. Over and over again. A...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
