Y16254K30000B9W datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> Y16254K30000B9W

Y16254K30000B9W: DescriptionFixed Resistor, Metal Foil, 0.3W, 4300ohm, 87V, 0.1% +/-Tol, -.2,.2ppm/Cel, 1206,; CategoryPassive components The resistor; File Size2MB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y16254K30000B9W Overview

Fixed Resistor, Metal Foil, 0.3W, 4300ohm, 87V, 0.1% +/-Tol, -.2,.2ppm/Cel, 1206,

Y16254K30000B9W Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	860424243
Reach Compliance Code	compliant
Country Of Origin	Israel
ECCN code	EAR99
YTEOL	10
structure	Chip
Number of terminals	2
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	0.64 mm
Package length	3.2 mm
Package form	SMT
Package width	1.57 mm
method of packing	Waffle Pack
Rated power dissipation(P)	0.3 W
resistance	4300 Ω
Resistor type	FIXED RESISTOR
series	VSMP
size code	1206
technology	METAL FOIL
Temperature Coefficient	0.2 ppm/°C
Terminal surface	TIN SILVER COPPER OVER NICKEL
Tolerance	0.1%
Operating Voltage	87 V

Preview

Download Datasheet

View All

VSMP Series (0603, 0805, 1206, 1506, 2010, 2018, 2512)

(Z-Foil)

Ultra High Precision Foil Wraparound Surface Mount Chip Resistor

with TCR of ± 0.05 ppm/°C and Power Coefficient of 5 ppm at

Rated Power and Load Life Stability of ± 0.005 % (50 ppm)

FEATURES



Temperature coefficient of resistance (TCR):

0.05 ppm/°C typical (0 °C to + 60 °C)

0.2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.)



Resistance tolerance: to ± 0.01 %



Power coefficient “R due to self heating”:

5 ppm at rated power



Power rating: to 750 mW at + 70 °C (see table 3)



Load life stability: to ± 0.005 % at 70 °C, 2000 h at rated

power



Resistance range: 5



to 125 k (for lower or higher

values, please contact us)



Vishay Foil resistors are not restricted to standard values,

we can supply specific “as required” values at no extra cost

or delivery (e.g. 1K2345 vs. 1K)



Thermal stabilization time < 1 s



(nominal value achieved within 10 ppm of steady state

value)



Electrostatic discharge (ESD) at least to 25 kV



Short time overload:



0.005 %



Non inductive, non capacitive design



Rise time: 1 ns effectively no ringing



Current noise: 0.010 µV

RMS

/V of applied voltage

(< - 40 dB)



Voltage coefficient < 0.1 ppm/V



Non inductive: < 0.08 µH



Non hot spot design



Terminal finishes available: lead (Pb)-free, tin/lead alloy



Matched sets are available on request



Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vpgsensors.com

Top View

(for date code print specification please refer to table 2)

INTRODUCTION

VSMP Series is the industry’s first device to provide high

rated power and excellent load life stability along with

extremely low TCR — all in one resistor.

One of the most important parameters influencing stability is

the Temperature Coefficient of Resistance (TCR). Although

the TCR of foil resistors is considered extremely low, this

characteristic has been further refined over the years. The

VSMP Series utilizes ultra high precision Bulk Metal

Z-Foil.

The Z-Foil technology provides a significant reduction of the

resistive element’s sensitivity to ambient temperature

variations (TCR) and to self heating when power is applied

(Power Coefficient of Resistance, or PCR). Along with the

inherently low PCR and TCR, Z-Foil technology also

provides remarkably improved load life stability, low noise

and tight tolerances.

The VSMP resistor has a full wraparound termination which

assures secure contact during the manufacturing process,

as well as providing stability during multiple thermal cyclings.

Vishay Foil Resistors' (VFR) application engineering

department is available to advise and make

recommendations. For non-standard technical requirements

and special applications, please contact VFR using the

e-mail address in the footer below.

Percent of Rated Power

TABLE 1 - TOLERANCE AND TCR VS.

RESISTANCE VALUE

(1)

(- 55 °C to + 125 °C, + 25 °C Ref.)

RESISTANCE

VALUE

()

250to 125K

100to < 250

50to < 100

25to < 50

10to < 25

5 to < 10

TOLERANCE

(%)

± 0.01

± 0.02

± 0.05

± 0.1

± 0.25

± 0.5

TYPICAL TCR AND

MAX. SPREAD

(ppm/°C)

± 0.2 ± 1.8

± 0.2 ± 2.8

± 0.2 ± 3.8

± 0.2 ± 7.8

FIGURE 1 - POWER DERATING CURVE

- 55 °C

100

- 75

+ 70 °C

- 50

- 25

+ 25 + 50 + 75 + 100 + 125 + 150 + 175

Ambient Temperature (°C)

* Pb containing terminations are not RoHS compliant; exemptions

may apply

Note

(1)

For tighter performances and non-standard values lower than



and above 125K, please contact VFR’s application

engineering using the e-mail addresses in the footer below

Document Number: 63060

Revision: 3-Mar-15

For any questions, contact

foil@vpgsensors.com

www.vishayfoilresistors.com

Recommended Resources

AC and DC power supply non-stop switching circuit using power supply coupler

Class A FET amplifier power supply circuit diagram

Wiring method for changing three-phase motor to single-phase operation_2

JA1 type (1kVA) AC voltage regulator circuit

Computer serial interface status indication circuit

CW1842 external MOS power tube single-ended reflection converter circuit

How to get the boot code of lm3sxxx series chips when building a project under IAR: As the title says, I want to use IAR EWARM to write LM3S code, but I don't know how to get the startup code file? It is automatically generated in keil. I hope someone who knows can tell me, thank you...; Fortware Microcontroller MCU

Application of EthernetPOWERLINK in machine control field: Application of EthernetPOWERLINK in machine control field...; EPACCN Industrial Control Electronics

A8+KSZ9021 network card driver problem: ping: sendto: No buffer space available ping: sendto: No buffer space available ping: sendto: No buffer space available 192.168.232.26: icmp_seq=28 ttl=64 time=0 ms 192.168.232.26: icmp_seq=29 ttl=64 ...; sundhhy DSP and ARM Processors

When I enter TCPMP, the waiting icon appears only for the first time. How can I make it appear every time?: When entering TCPMP, the waiting icon only appears for the first time. How can I make it appear every time? When exiting TCPMP, the process has been closed. Thank you!...; lxchina Embedded System

How to use EVC to implement a radar scanning effect interface?: How should I draw the scan line in the middle so that it can rotate continuously? See the attached picture for the effect....; kaixiongwu Embedded System

The following compilation error occurs in the dialog-based MFC application under CE6.0. How to solve it? Please give me some advice.: The dialog-based MFC application under CE6.0 has the following compilation error. How to solve it? Please give me some advice. My SDK is compiled using the DEVICEEMULATOR bsp based on the arm s3c2410 ...; donglele2005 Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components