The waveform after mixing two same-phase sine wave signals through the multiplication chip AD633 must have a DC component, right? How to separate the DC component? The waveform obtained by the ring di...
Inductive proximity sensors can be used for contactless detection of metal near LC sensors. These inductive sensing solutions enable presence detection and task counting on factory assembly lines with...
I searched online, but to no avail:Sad: For example:Here, CLK_counter increments by 1 for each input clock cycle, but I think there is a problem and want to observe this signal. The TestBench automati...
[align=left]Hello experts, I am analyzing the openpilot source code and found the following code: [/align][align=left][font=新宋体]OPLinkSettingsData oplinkSettings;[/font][/align][align=left][font=新宋体] ...
The oscilloscope is normal and can see the scan lines. However, when observing the measured signal, only the scan lines can be seen but not the waveform. Why is this?...
[i=s] This post was last edited by lb8820265 on 2017-4-22 12:47 [/i] [align=left][font=微软雅黑][size=3]First, here is the video: [/size][/font][/align][align=left][align=center][font=微软雅黑][size=3][media=...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
As people's requirements for safety and comfort in the process of driving cars continue to increase, automotive radars are widely used in the car's adaptive cruise system, collision avoidance syste...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]