EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL8ALF-03-1130-F-

Description
Array/Network Resistor, Isolated, Thin Film, 0.16W, 113ohm, 1% +/-Tol, -25,25ppm/Cel, 4430,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUB-GL8ALF-03-1130-F- Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 113ohm, 1% +/-Tol, -25,25ppm/Cel, 4430,

GUB-GL8ALF-03-1130-F- Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid795602114
package instructionSMT, 4430
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.2
structureMolded
JESD-609 codee3
Network TypeIsolated
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length11.176 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.16 W
resistance113 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4430
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance1%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
[PSoC4 Experience] Virtual Voltmeter
PSoC4 Virtual Voltmeter Watching the video first and then reading the article may make it easier for you to understand http://v.youku.com/v_show/id_XNjIyNzAzNDUy.html 1.1 Purpose and Function of the E...
fsyicheng MCU
Automatic charger and discharger for nickel-cadmium batteries
This circuit can automatically disconnect the charging or discharging circuit of two nickel-cadmium batteries when they are charged to 3V or discharged to 1.34V, effectively preventing overcharging or...
zzzzer16 Analog electronics
What is the relationship between AVR's ISP and jtga interfaces?
When I was referring to the design of an AVR (ATMEGA644PA-AU) chip, I found that the ISP download line uses the SPI port, which is the interface of PIN1, PIN2, and PIN3, while the JTAG interface in th...
bigbat Microchip MCU
【KW41Z】Walking instrument 2
The Bluetooth part of KW41Z is finally completed. Actually, it can’t be said to be completed. It is just a transplantation of an existing example. Upload regularly after Bluetooth connection [code]ext...
dvd1478 NXP MCU
Ask a question about the IO of C8051F microcontroller
As the title says, I read the PDF document of C8051F and found that the power supply voltage of C8051F can be 3.3V-5V, but the IO voltage of C8051F is not mentioned in the PDF. So, what is the IO volt...
oldcat 51mcu
ATMEGA128A's crystal oscillator does not oscillate
For the reset circuit already added to the schematic diagram, connect the reset circuit according to the DMAVR schematic diagram...
mingmingyama Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1864  2218  1512  2100  2401  38  45  31  43  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号