EEWORLDEEWORLDEEWORLD

Part Number

Search

P8-V732523

Description
Special Switch, Momentary
CategoryMechanical and electronic products    switch   
File Size713KB,2 Pages
ManufacturerOTTO
Websitehttp://www.ottoexcellence.com
Environmental Compliance
Download Datasheet Parametric View All

P8-V732523 Overview

Special Switch, Momentary

P8-V732523 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerOTTO
Reach Compliance Codeunknown
Actuator length0.078 inch
Actuator typePUSHBUTTON
Casing type3/4-20
Dielectric withstand voltage1050VRMS V
Electrical life25000 Cycle(s)
JESD-609 codee4
Manufacturer's serial numberP8
Maximum operating temperature85 °C
Minimum operating temperature-55 °C
Switch actionMOMENTARY
Terminal surfaceGold (Au)
Base Number Matches1
VANDAL RESISTANT PUSHBUTTONS
The P8 Vandal Resistant series is a durable, robust switch,
offering the same quality and precision tactile feedback found
in the standard P8 series. With a variety of case, mounting and
terminal styles and a mechanical life of 1,000,000 cycles, this
stainless steel sealed switch is ideal for door access security
systems, public transit systems, emergency phones, traffic
signals, industrial and process control environments and
anywhere that ruggedness, durability and security are crucial.
OTTO P8 series pushbutton switches feature a shortened
back of panel depth while offering all the features of the
regular size P1 and P3 series switches. P8 series switches offer
vastly improved electrical and mechanical life under extreme
conditions found in most military and industrial environments.
On sealed models, a silicone boot operating on our patented
“rolling sleeve” principle protects the contact area against
contamination at the button area. This boot provides long life
and smooth operation over a wide temperature range. Sealed
terminals protect the contact area from hostile environments and
solder flux on both sealed and unsealed models.
High contact force (120g/4.2 oz), low contact resistance
(25mΩ) and short contact bounce (5ms max) are all a result
of our snap-action mechanism. These characteristics provide
exceptional current carrying capabilities over the life of the
switch. Optional low level (gold plate) configuration makes the
P8-V switches well suited to interface directly to computers and
other solid state devices.
Standard Characteristics/Ratings:
ELECTRICAL RATINGS:
Load
Resistive
Inductive
Lamp
DWV
Low Level
Electrical Life:
Mechanical Life:
Seal:
Operating Force:
Total Travel:
Overtravel:
Sea Level @ 28VDC
or 115VAC, 60/400Hz
10A
5A
3A
1050Vrms
10mA @ 30mV
100,000 cycles (25,000 low level)
1,000,000 cycles
IP64 or IP68S
2.5 lbs. +0.5 /-1.0 lb. or 4.0 lbs. +/- 1.0 lb.
0.085 +/- 0.015 inches
0.012 inches min
COMPACT
PUSHBUTTONS
P8-V
MOMENTARY ACTION, SHORTER BEHIND PANEL, SUBMINIATURE DOUBLE BREAK, SNAP-ACTION
Flush Mount,
5/8” Thread Shown
®
C
US
Operating Temp Range:
-55°C to +85°C
Features:
• Stainless steel vandal resistant case
• Aluminum security level case
• Watertight to IP68S or moistureproof & dusttight
to IP64
• Positive tactile feedback
• Less than 25mΩ contact resistance
• Variety of case and button styles available
• Mechanical life 1 million cycles
• UL recognized & CSA certified
• UL1500 ignition protected
• RoHS/WEEE/Reach compliant
Movement Differential:
0.015 inches min
MATERIALS:
Case:
Button:
Terminals:
Terminal Hardware:
Mounting Hardware:
Anodized aluminum alloy or stainless steel
Anodized aluminum alloy or stainless steel
Standard silver plate or optional gold plate for
low level applications
Terminal lugs, screws and lockwasher when applicable
Hex nut, lockwasher and panel seal gasket when applicable
PUSHBUTTONS
Specifications Subject To Change Without Notice
www.ottoexcellence.com
137
Please tell me about the power chip in the barley box
224540 The UP10 above has CU3ZL written on the chip (I looked for it on alldatasheetcn.com and ICkey, but couldn't find it). The capacitor next to the 6-pin is 220, and the inductor is 4R7 (it should ...
lidonglei1 Power technology
A spike voltage appears when the current of a single-phase bridge phase-controlled rectifier resistor and inductive load is interrupted
[i=s]This post was last edited by Dahanchong on 2019-4-28 10:04[/i] I am a student, and when I was simulating a single-phase bridge rectifier, I encountered the phenomenon shown in the picture. How do...
大寒虫 Analog electronics
Help: Wireless chip transceiver debugging information
Help: I need information about wireless chip transceiver debugging. I am doing my graduation project, which includes wireless transceiver. I plan to use wireless remote control to implement it. The tr...
fenglin51 Embedded System
Is there a signal after the LINUX system time is changed?
When using alarm() to set a timer, if the system time is changed, there will be a series of problems with recalculating the time. Is there such a signal to notify "the LINUX system time has been chang...
qinxuewei101 Linux and Android
How to specify the network address of the Zigbee module so that Zigbee can run at this network address after joining the network?
What if I want to fix the network address of this Zigbee module during development so that the module can run with this specified network address after connecting to the network?...
leolei1986 RF/Wirelessly
C8051F310 In-System Flash Programming
C8051F310 In-System Flash Programming When using a single-chip microcomputer, some data needs to be set so that it will not be lost when the power is off. Generally, the first thing that comes to mind...
David_Lee MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2583  2889  2454  784  2425  52  59  50  16  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号