Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
I am a novice who wants to make an electronic scale with a single chip microcomputer, but I don't know where to start. Please provide some solutions, information, etc. Or tell me the general direction...
At present, the vc environment of raw-os + fatfs has been built and can run normally. The vc environment of sqlite can also run, but it is based on the windows file system. Now we need to strip sqlite...
As shown in the picture, I made a function generator to generate a sine wave with a bias of 0 and an amplitude of 2V.
Two resistors are added externally to provide a 10V bias.
I thought that adding th...
[font=Tahoma, Helvetica, SimSun, sans-serif][size=14px]The board provides AUD_PWM and AUD_SD interfaces related to audio. The former writes data and the latter controls the enable state. [/size][/font...
Double Eleven Forum, I love to buy boards Board 1: RL78/G14 board, Renesas, I have never used Renesas development boards before, I bought this to practiceBoard 2: [b]Microchip's MCP19111 evaluation bo...
In the past few days, the news that ZTE was "banned" by the US Department of Commerce has triggered widespread reflection and concern in various domestic industries about the lack of independent co...[Details]
The most significant event in the technology circle during this period is undoubtedly the news that ZTE was banned by the United States. Once the news came out, it shocked the entire Chinese techno...[Details]
Recently, the results of the 2018 German Red Dot Design Award were announced. GoodWe, a company located in Suzhou High-tech Zone, stood out among thousands of outstanding design products from 5...[Details]
On April 20, the Photovoltaic Summit, guided by Jiangsu Renewable Energy Industry Association, hosted by Growatt, and supported by LONGi Solar Technology Co., Ltd. and Jiangsu Bigo New Energy Group...[Details]
1. Usage scenarios In the first case, when using a common STM32 delay function, similar to HAL_Delay(time), since this function uses a loop to judge and delay, when executing this function, the ent...[Details]
Because the STM32 HAL library only has millisecond-level delay for HAl_Delay(), in order to achieve accurate microsecond-level delay, Systick has to be modified. However, since it is used internally ...[Details]
From last year to now, competition in the photovoltaic inverter industry has become increasingly fierce. In addition to the introduction of new products, various marketing and promotion methods hav...[Details]
In the Huaxing Optoelectronics LCD panel
factory
located in Guangming New District, Shenzhen
, apart from a few people repairing machines, it is often difficult to see other people. Here, ev...[Details]
This program is used in the development board to generate sounds of different frequencies. The overall program is relatively simple, mainly using two timers. The code and my comments are as follows. ...[Details]
China Energy Storage Network News:
On the 7th, Jurong Economic Development Zone signed a strategic cooperation framework agreement on comprehensive energy services with State Grid Jiangsu Int...[Details]
The implementation of CAN driver under embedded operating system Android requires not only adding CAN driver device in Linux kernel, but also implementing the call of Android HAL layer. Taking S5...[Details]
In recent years, in order to meet the needs of social development, more and more companies have entered the fields of smart phones, artificial intelligence,
VR
, AR, etc. After seeing the d...[Details]
On the eve of 5G
commercialization,
ZTE
has established and adhered to
the
5G
pioneer strategy, focusing on
5G
end-to-end solutions, and investing in standard setting, ...[Details]
1. Heart rate measurement principle 1. What is a heart rate module? The heart rate module is professionally used to monitor the heart rate of the wrist, fingers, forehead, earlobe, chest and other ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
