• Bidirectional/differential data strobe per byte of
data (DQS/DQS#)
• Programmable READ and WRITE latencies (RL/WL)
• Programmable burst lengths: 4, 8, or 16
• Per-bank refresh for concurrent operation
• On-chip temperature sensor to control self refresh
rate
• Partial-array self refresh (PASR)
• Deep power-down mode (DPD)
• Selectable output drive strength (DS)
• Clock stop capability
• RoHS-compliant, “green” packaging
Table 1: Key Timing Parameters
Speed
Grade
-18
2
-25
-3
Clock
Rate
(MHz)
533
400
333
Data Rate
(Mb/s/pin) RL WL
1066
800
667
8
6
5
4
3
2
Options
• V
DD2
: 1.2V
• Configuration
– 16 Meg x 16 x 8 banks x 1 die
– 8 Meg x 32 x 8 banks x 1 die
– 8 Meg x 32 x 8 banks x 2 die
– 16 Meg x 16 x 8 banks x 4 die
– 8 Meg x 32 x 8 banks x 2 die
– 8 Meg x 32 x 8 banks x 3 die
– 8 Meg x 32 x 8 banks x 4 die
– 16 Meg x 16 x 8 banks x 2 die +
8 Meg x 32 x 8 banks x 1 die
• Device type
– LPDDR2-S4, 1 die in package
– LPDDR2-S4, 2 die in package
– LPDDR2-S4, 3 die in package
– LPDDR2-S4, 4 die in package
• FBGA“green” package
– 134-ball FBGA (11mm x 11.5mm)
– 134-ball FBGA (11.5mm x 11.5mm)
– 168-ball FBGA (12mm x 12mm)
– 168-ball FBGA (12mm x 12mm)
– 168-ball FBGA (12mm x 12mm)
– 216-ball FBGA (12mm x 12mm)
– 216-ball FBGA (12mm x 12mm)
– 216-ball FBGA (12mm x 12mm)
– 220-ball FBGA (14mm x 14mm)
– 220-ball FBGA (14mm x 14mm)
• Timing – cycle time
– 1.875ns @ RL = 8
– 2.5ns @ RL = 6
– 3.0ns @ RL = 5
• Operating temperature range
– From –25°C to +85°C
– From –40°C to +105°C
• Revision
Notes:
Marking
L
128M16
64M32
128M32
256M32
64M64
96M64
128M64
192M32
D1
D2
D3
D4
MH
MG
KL
LE
KP
KH
KJ
KU
MP
LD
-18
2
-25
-3
IT
AT
:A
t
RCD/
t
RP
1
Typical
Typical
Typical
1. For fast
t
RCD/
t
RP, contact factory.
2. For -18 speed grade, contact factory.
PDF: 09005aef83f3f2eb
2gb_mobile_lpddr2_s4_g69a.pdf – Rev. N 3/12 EN
1
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2010 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
2Gb: x16, x32 Mobile LPDDR2 SDRAM S4
Features
Table 2: Single Channel S4 Configuration Addressing
128 Meg x 16
Figure 3
(page 16)
CS0#
CS1#
Row addressing
Column ad-
dressing
Number of die
Die per
rank (CS#)
Ranks per
channel
1
CS0#
CS1#
CS0#
CS1#
16 Meg x 16 x 8
banks
na
16K (A[13:0])
1K (A[9:0])
na
1
1
0
1
64 Meg x 32
Figure 3
(page 16)
8 Meg x 32 x 8
banks
na
16K (A[13:0])
512 (A[8:0])
na
1
1
0
1
128 Meg x 32
Figure 4
(page 17)
8 Meg x 32 x 8
banks
8 Meg x 32 x 8
banks
16K (A[13:0])
512 (A[8:0])
512 (A[8:0])
2
1
1
2
192 Meg x 32
Figure 6
(page 19)
16 Meg x 16 x 8
banks x 2
8 Meg x 32 x 8
banks
16K (A[13:0])
1K (A[9:0])
512 (A[8:0])
3
2
1
2
256 Meg x 32
Figure 9
(page 22)
16 Meg x 16 x 8
banks x 2
16 Meg x 16 x 8
banks x 2
16K (A[13:0])
1K (A[9:0])
1K (A[9:0])
4
2
2
2
Architecture
Die configu-
ration
Table 3: Dual Channel S4 Configuration Addressing
Architecture
Die configuration
Row addressing
Column
addressing
Number of die
Die per
rank (CS#)
Ranks per
channel
1
Note:
CS0#
CS1#
Channel A
Channel B
CS0#
CS1#
64 Meg x 64
Figure 5 (page 18)
8 Meg x 32 x 8 banks
16K (A[13:0])
512 (A[8:0])
na
2
1
0
1
1
96 Meg x 64
Figure 8 (page 21)
8 Meg x 32 x 8 banks
16K (A[13:0])
512 (A[8:0])
512 (A[8:0])
3
1
1-chan A, 0-chan B
2
1
128 Meg x 64
Figure 7 (page 20)
8 Meg x 32 x 8 banks
16K (A[13:0])
512 (A[8:0])
512 (A[8:0])
4
1
1
2
2
1. A channel is a complete LPDRAM interface, including command/address and data pins.
See Package Block Diagrams (page 16) for descriptions of signal connections and die configurations for each re-
spective architecture.
PDF: 09005aef83f3f2eb
2gb_mobile_lpddr2_s4_g69a.pdf – Rev. N 3/12 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2010 Micron Technology, Inc. All rights reserved.
2Gb: x16, x32 Mobile LPDDR2 SDRAM S4
Features
Part Numbering
Figure 1: 2Gb LPDDR2 Part Numbering
MT
Micron Technology
Product Family
42 = Mobile LPDDR2 SDRAM
42
L
128M16 D1
KL
-25
IT
:A
Design Revision
:A = First generation
Operating Temperature
IT = –25°C to +85°C
AT = –40°C to +105°C
Operating Voltage
L = 1.2V
Cycle Time
Configuration
128M16 = 128 Meg x 16
64M32 = 64 Meg x 32
128M32 = 128 Meg x 32
256M32 = 256 Meg x 32
192M32 = 192 Meg x 32
64M64 = 64 Meg x 64
96M64 = 96 Meg x 64
128M64 = 128 Meg x 64
Package Codes
MH = 134-ball FBGA, 11mm x 11.5mm
MG = 134-ball FBGA, 11.5mm x 11.5mm
KL, KP, LE = 168-ball FBGA, 12mm x 12mm
KH, KJ, KU = 216-ball FBGA, 12mm x 12mm
LD, MP = 220-ball FBGA, 14mm x 14mm
-18 = 1.8ns,
t
CK RL = 8
t
-25 = 2.5ns,CK RL = 6
t
-3 = 3.0ns,CK RL = 5
Addressing
D1 = LPDDR2, 1 die
D2 = LPDDR2, 2 die
D3 = LPDDR2, 3 die
D4 = LPDDR2, 4 die
FBGA Part Marking Decoder
Due to space limitations, FBGA-packaged components have an abbreviated part marking that is different from the
part number. Micron’s FBGA part marking decoder is available at
www.micron.com/decoder.
In timing diagrams, “CMD” is used as an indicator only. Actual signals occur on CA[9:0].
V
REF
indicates V
REFCA
and V
REFDQ
.
PDF: 09005aef83f3f2eb
2gb_mobile_lpddr2_s4_g69a.pdf – Rev. N 3/12 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2010 Micron Technology, Inc. All rights reserved.
2Gb: x16, x32 Mobile LPDDR2 SDRAM S4
Features
Contents
General Description ....................................................................................................................................... 11
General Notes ............................................................................................................................................ 11
Write Data Mask ............................................................................................................................................. 67
READ Burst Followed by PRECHARGE ......................................................................................................... 69
WRITE Burst Followed by PRECHARGE ....................................................................................................... 70
Auto Precharge ........................................................................................................................................... 71
READ Burst with Auto Precharge ................................................................................................................. 71
WRITE Burst with Auto Precharge ............................................................................................................... 72
Temperature Sensor ................................................................................................................................... 87
Deep Power-Down ........................................................................................................................................ 101
Input Clock Frequency Changes and Stop Events ............................................................................................ 102
Input Clock Frequency Changes and Clock Stop with CKE LOW .................................................................. 102
Input Clock Frequency Changes and Clock Stop with CKE HIGH ................................................................. 103
NO OPERATION Command ........................................................................................................................... 103
Simplified Bus Interface State Diagram ....................................................................................................... 103
Truth Tables .................................................................................................................................................. 105
Input Signal .............................................................................................................................................. 121
AC and DC Logic Input Measurement Levels for Differential Signals ................................................................ 123
Single-Ended Requirements for Differential Signals .................................................................................... 124
Differential Input Crosspoint Voltage ......................................................................................................... 126
Clock Period Jitter .......................................................................................................................................... 138
Clock Period Jitter Effects on Core Timing Parameters ................................................................................. 138
Cycle Time Derating for Core Timing Parameters ........................................................................................ 139
Clock Cycle Derating for Core Timing Parameters ....................................................................................... 139
Clock Jitter Effects on Command/Address Timing Parameters ..................................................................... 139
Clock Jitter Effects on READ Timing Parameters .......................................................................................... 139
Clock Jitter Effects on WRITE Timing Parameters ........................................................................................ 140
AC Timing ..................................................................................................................................................... 142
CA and CS# Setup, Hold, and Derating ........................................................................................................... 149
Data Setup, Hold, and Slew Rate Derating ....................................................................................................... 156
Revision History ............................................................................................................................................ 163
Rev. N, Production – 3/12 ........................................................................................................................... 163
Rev. M, Production – 10/11 ........................................................................................................................ 163
Rev. L, Production – 09/11 .......................................................................................................................... 163
Rev. K, Production – 08/11 ......................................................................................................................... 163
Rev. J, Production – 05/11 .......................................................................................................................... 163
Rev. H, Production – 3/11 ........................................................................................................................... 163
Rev. G, Production – 1/11 ........................................................................................................................... 163
Could you please tell me the winding method and other parameters of the EE8 transformer that can be used to increase the voltage from 0.7V to 7V? The more detailed the better. Thank you!...
I recently looked at the schematic diagram of the C8051F350 microcontroller development board. I don't understand what the polarity capacitor in the reference voltage input circuit does. Please tell m...
Definition of switching power supply :
The switching power supply is used throughThe circuit controls the switch tube to conduct and cut off at high speed, converting the DC power into high-frequency ...
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
Leakage current is generated by parasitic resistance paths between the measurement circuit and a nearby voltage source. This current can significantly reduce the accuracy of low current measurement...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
