177-714-5-21GP4J5-24SNG datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-714-5-21GP4J5-24SNG

177-714-5-21GP4J5-24SNG: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-714-5-21GP4J5-24SNG Overview

Interconnection Device

177-714-5-21GP4J5-24SNG Parametric

Parameter Name	Attribute value
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

Discharge type front memory circuit

Overcurrent protection circuit for generator low voltage starting a

sound exciter

Minsk brand MNHCK-15 refrigerator circuit

HFC5230 "Please note there is a fault" language integrated circuit

Switching transistor bridge DC servo motor controller circuit diagram

Multi-channel 4-20mA signal acquisition problem: As shown in the figure, there are 4 4-20mA signals from the transmitter , which are connected in series with 4 250R sampling resistors , and then sent to the 4 input channels of the single-ended input...; willzhang 51mcu

【Article】LED display screen controller design based on Nios II: Based on μC/OS2II real-time operating system, the multi-task management operation mode is realized, and Nios II 32-bit processor is used as the core of LED display screen control system to control the...; 红色飓风 Red Hurricane FPGA Zone

Sitara, the story behind the naming of TI's ARM processor family: When TI first released processors with ARM cores through its DSP department, the product family was named DaVinci. When TI released high-performance ARM processors through its DSP department, the prod...; 潇噶 DSP and ARM Processors

【Design Tools】XILINX Development Board ISE9.0 Installation Video Tutorial: [flash]http://player.youku.com/player.php/sid/XMjQ4MzE1MDky/v.swf[/flash]...; 鑫海宝贝 FPGA/CPLD

C8051F020 MCU Paper: [i=s]This post was last edited by paulhyde on 2014-9-15 08:56[/i] Hehe, share it:lol :lol...; xiaoxiaoha Electronics Design Contest

LPC2146 uses GPIO port to control LCD. I have some problems. Please give me some advice. Thank you.: //******Check busy****/// void busy() { p_di=0; p_rw=1; while(1) { p_e=1; if(Data<0x80)break; p_e=0; } p_e=0; } This is a reference code for MCU, #define Data P0 The reference code defines the PO port...; heima3041 Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components