5.0 mm x 3.2 mm Package Pinout ............................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
Device Configurations and Pin-outs ............................................................................................................................................. 9
Pin-out Top Views................................................................................................................................................................. 9
Test Circuit Diagrams for LVCMOS and Clipped Sinewave Outputs ......................................................................................... 10
Frequency Stability ............................................................................................................................................................. 16
Output Frequency and Format............................................................................................................................................ 16
Output Frequency Tuning ................................................................................................................................................... 16
Pin 1 Configuration (OE, VC, or NC) .................................................................................................................................. 17
Control Voltage Bandwidth ................................................................................................................................................. 20
Pull Range and Average Pull Range .................................................................................................................................. 22
Output Frequency ............................................................................................................................................................... 23
2
I C Control Registers .......................................................................................................................................................... 25
Serial Interface Configuration Description .......................................................................................................................... 28
Serial Signal Format ........................................................................................................................................................... 28
Parallel Signal Format ........................................................................................................................................................ 29
Parallel Data Format ........................................................................................................................................................... 29
2
I C Timing Specification ...................................................................................................................................................... 31
2
I C Device Address Modes ................................................................................................................................................. 32
Schematic Example ............................................................................................................................................................ 33
Dimensions and Patterns ........................................................................................................................................................... 34
Additional Information ................................................................................................................................................................ 36
Revision History ......................................................................................................................................................................... 37
Rev 1.05
Page 3 of 38
www.sitime.com
SiT5156
1 MHz to 60 MHz, ±0.5 to ±2.5 ppm, Elite Platform™ Super-TCXO
Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and 3.3V Vdd.
Table 1. Output Characteristics
Parameters
Nominal Output Frequency Range
Operating Temperature Range
Symbol
F_nom
T_use
Min.
1
-20
-40
-40
Frequency Stability over
Temperature
Initial Tolerance
Supply Voltage Sensitivity
F_stab
–
–
–
F_init
F_Vdd
–
–
–
–
Output Load Sensitivity
F_load
–
–
–
Frequency vs. Temperature Slope
ΔF/ΔT
–
–
–
Dynamic Frequency Change during
Temperature Ramp
One-Year Aging
20-Year Aging
F_dynamic
–
–
–
F_1y
F_20y
–
–
Typ.
–
–
–
–
–
–
–
–
±7.10
±11.83
±28.40
±0.81
±1.35
±3.24
±15
±25
±60
±0.13
±0.21
±0.50
±1
±2
Max.
60
+70
+85
+105
±0.5
±1.0
±2.5
±1
±16.25
±32.50
±65.0
±2.75
±5.50
±11.00
±25
±50
±100
±0.21
±0.42
±0.83
–
–
Unit
MHz
°C
°C
°C
ppm
ppm
ppm
ppm
ppb
ppb
ppb
ppb
ppb
ppb
ppb/°C
ppb/°C
ppb/°C
ppb/s
ppb/s
ppb/s
ppm
ppm
Initial frequency at 25°C at 48 hours after 2 reflows
[color=#000] You need a voltage reference, but you’re not sure how to choose the best one for your application. Then you’ve come to the right place! In this blog post, I’ll discuss some key voltage re...
POR&PUC POR is the power-on reset signal, which is only generated when the following three events occur: 1. The chip is powered on. 2. -RST/NMI is set to reset mode, and a low-level signal appears on ...
Using 51 MCU to simulate I2C timing to control opt3001 light sensor, the data captured by logic analyzer shows that opt3001 does not feedback ACK to MCU. What is the most likely problem in this case? ...
[size=4]Question: About RS485[/size] [size=4]Use a resistor to pull up[/size] [size=4]B uses a resistor to pull down[/size] [size=4]A and B are connected by resistors, [/size] [size=4]What are the app...
The first MicroPython book will be available on Amazon soon. sans-serif]This practical guide introduces programming with MicroPython on the open source hardware platform pyboard. The book explains ste...
Dual-mode inverters can operate both in conjunction with the grid and independently. These inverters can inject excess energy from renewable energy and storage devices into the grid, and withdraw p...[Details]
Wave soldering is a crucial electronic component soldering technique used in the production of a wide range of electronic devices, from home appliances to computers to avionics. The process is wide...[Details]
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
summary
There are multiple approaches to making industrial systems more intelligent, including applying artificial intelligence (AI) technology at the edge and in the cloud to sensor...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
Electric vehicles are now widespread, but they've brought with them a host of problems, the most prominent of which is charging. Small electric vehicles (EVs) are a new form of transportation in a ...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
In the field of intelligent driving, regulations are becoming increasingly stringent, and the technical threshold continues to rise. Especially after the traffic accident in March 2025, the Ministr...[Details]
With the increasing popularity of automated equipment, linear modules, a common auxiliary device for automated equipment, have also seen a bright future. In particular, in recent years, many small ...[Details]
In daily life, when we purchase a transformer, we are faced with the installation and wiring procedures. Generally speaking, large transformers such as power transformers are equipped with speciali...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
Compiled from semiengineering
The industry is increasingly concerned about power consumption in AI, but there are no simple solutions. This requires a deep understanding of software and ...[Details]
Nidec Precision Testing Technology Co., Ltd. will participate in "Testing Expo China—Automotive 2025" to be held at the Shanghai World Expo Exhibition and Convention Center from August 27 (Wednesda...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
