EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SLALC2725

Description
Transponder, LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-SLALC2725 Overview

Transponder, LC/SPC Connector,

PH1-SLALC2725 Parametric

Parameter NameAttribute value
Objectid4000964595
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsOC-192, SONET
Connection TypeLC/SPC CONNECTOR
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1531 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
stm32 serial port problem
Using the serial port 1 of stm32, interrupt mode. Every time after burning the program, I can receive 00 characters through the serial port debugging assistant. What's going on? Thank you. . . ....
Stm32Learner MCU
Now we need to power a dual-powered op amp, which requires a +5V input and -5v output charge pump chip.
[size=4]The project needs to use an op amp powered by both positive and negative power supplies. The positive power supply is +5 volts from the USB input. The charge pump chip used before was TC7662A ...
小浅白白 Power technology
Light gate counter
Light-controlled counter...
意想不到1 MCU
Discussion on Current Detection Circuit in Switching Power Supply
Abstract: This paper introduces the implementation method of the current detection circuit, and discusses the problems of current transformer saturation and secondary current droop that are often enco...
zbz0529 Test/Measurement
I would like to ask about the problem of PWM control LED based on register configuration.
I just want to ask if I need to use the IO port to turn on the LED light after the PWM registers are configured?Or can I just use PWM to dim and brighten the LED, turn the light on and off?Why can I o...
一百年后的自己 51mcu
Popular Science | IoT Architecture and Technical Protocols
With the continuous development of science and technology, especially the birth of 5G , the expansion of the number and coverage of the Internet of Things has brought unprecedented challenges to the I...
alan000345 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1452  1864  1914  2248  323  30  38  39  46  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号