EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7LASA2725

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-7LASA2725 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-7LASA2725 Parametric

Parameter NameAttribute value
Objectid1871044643
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1531 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Which one is better for step-down output of 5V, MAX797HESE or TPS40055? What should be considered when selecting?
Which one is better for step-down output of 5V, MAX797HESE or TPS40055? What should be considered when selecting? What should be paid attention to when making circuit boards? Here is a specific questi...
刘启烨 Power technology
RM48 failure rate
Recently, there are products made of RM48 chips, and their reliability needs to be evaluated, but how can we obtain their failure rate and fault coverage? In addition, I found a method for predicting ...
ml0943 Microcontroller MCU
(There are three lights in the room, how to distinguish them) How to solve this interview question? ?
[i=s]This post was last edited by viphotman on 2019-3-8 11:38[/i] [align=left]I saw this question in the forum, but couldn't find the answer; I found the answer on the Internet;[/align] [align=left]Qu...
viphotman Talking about work
About JK Flip-Flops
For the circuit in the figure below, if the Q terminal is required to output a low level when CLK is connected to a low level, how should the trigger be connected? (Or when CLK is connected to a high ...
qy08301 Power technology
EEWORLD University Hall----Live Replay: Littelfuse Silicon Carbide (SiC) MOSFET and Schottky Diode Product Introduction and Related Applications
Live replay: Littelfuse Silicon Carbide (SiC) MOSFET and Schottky Diode product introduction and related applications : https://training.eeworld.com.cn/course/4811...
hi5 Integrated technical exchanges
I would like to ask about the thread. How can I activate the thread?
在一个函数中定义一个线程 m_dwThreadId=0 m_hThread = CreateThread( NULL, 0, CGraphManager::ThreadProc, this, 0, &m_dwThreadId );具体函数: Init() {HRESULT hr = S_OK;RETAILMSG(1,(L"CGraphManager::Init() "));// Create th...
eaglewxy Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 567  1795  2483  762  1592  12  37  50  16  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号