EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7LHFA2725

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-7LHFA2725 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,

PH1-7LHFA2725 Parametric

Parameter NameAttribute value
Objectid1871045019
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1531 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Ask for help from serial port experts
Has anyone used TI's TL16C554 chip? I've been tormented by this for a long time and haven't solved it yet. I use it on my own DSP board. 554 will not make mistakes when sending data, but when 554 rece...
uuiikid Embedded System
Windows CE and its development tools.pdf
Windows CE and its development tools.pdf...
yuandayuan6999 MCU
About atmel burning problem
I just bought an at89lv51, but I always get errors when programming on the stc development board. What could be the reason? Is it a voltage problem? Or is it a problem with the programming driver or t...
yangprime 51mcu
Seven Zongzi------Showing Gifts
In line with the principle of giving without giving, I'm showing off the gifts I exchanged for my chip coins. This time, my chip coins are only enough for this level, but the packaging is exquisite. E...
ddllxxrr Talking
msp430g2101 MCU, flash chip using FET-Pro430 software, program can erase, but read and write both fail
读的空白时候显示 ===================================== JTAG communication initialization.... OK Verifying Security Fuse .................... OK All memory Blank checking............. failed --,,-- without pro...
fish001 Microcontroller MCU
ADC has three interrupts INT1.6 and INT1.1 INT1.2. I can't tell them apart. Could you please give me some advice?
Everyone, I have encountered some problems when studying the ADC module recently. The 28335ADC module can generate three interrupts. They are the ADC interrupt of INT1.6, the SEQ2 interrupt of INT1.2 ...
jonny0811 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1914  1627  1185  2109  1916  39  33  24  43  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号