EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MS2SA4245

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-MS2SA4245 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-MS2SA4245 Parametric

Parameter NameAttribute value
Objectid1871065105
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1561 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Discussion on PCB layout for weak signal measurement
[table=98%,rgb(238, 238, 238)] [tr][td] For PCB layout (op amp, AD, DA, reference) of weak signal measurement (μV or even nV level), can the reference be laid on a separate layer (4-layer board)? Will...
zca123 PCB Design
BGA DIY manual soldering problem solving
[i=s] This post was last edited by Qingye Piaoling on 2015-4-21 11:07 [/i] After a long period of thinking and improvement of comprehensive ability. The difference in success rate between BGA manual s...
青叶漂零 DIY/Open Source Hardware
I would like to ask everyone, which direction is better to develop in, software engineering or embedded system?
I am from the Department of Computer Science. In my junior year, I was divided into two majors: software engineering and embedded system. I would like to know more about what the two majors are about....
flyingxc82 Embedded System
CRC - Is this a bug?
Using STM32F103ZET6, the code is as follows int main(void) { int getdr; RCC_AHBPeriphClockCmd( RCC_AHBPeriph_CRC , ENABLE); CRC->CR = 1; CRC->DR = 0x0; getdr = CRC->DR; while (1){} } Including turning...
akatosh stm32/stm8
【Help】Everyone come in and help
I am making a simple gadget that communicates via the UART port. There is no RESET button on the 149 circuit, so it is reset by power-on.The program is written and the hardware simulation is true, wit...
会流泪的鱼 Microcontroller MCU
Production of single-phase variable frequency power supply
[i=s]This post was last edited by paulhyde on 2014-9-15 04:18[/i] This is the first time we have worked on a power supply topic, and it is a topic known as the most difficult power supply. The inverte...
liuyong1989 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1477  53  2242  1086  1307  30  2  46  22  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号