PH1-SS2SA2721 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Optical fiber> PH1-SS2SA2721

PH1-SS2SA2721: DescriptionTransponder, SC/UPC Connector,; CategoryWireless rf/communication Optical fiber; File Size240KB，6 Pages; ManufacturerJDS Uniphase Corporation ( VIAVI ); Websitehttp://www.jdsu.com/index.html

Download Datasheet Parametric View All

PH1-SS2SA2721 Overview

Transponder, SC/UPC Connector,

PH1-SS2SA2721 Parametric

Parameter Name	Attribute value
Objectid	1871081876
Reach Compliance Code	compliant
Other features	IT ALSO OPERATE FROM 1280NM TO 1600NM
body width	56.1 mm
body height	13.2 mm
Body length or diameter	76.5 mm
Communication standards	GR-253, OC-192, SONET
Connection Type	SC/UPC CONNECTOR
Fiber optic equipment types	TRANSCEIVER, TRANSPONDER
Nominal operating wavelength	1531 nm
Nominal optical power output	0.562 mW
minimum return loss	-27 dB

Preview

Download Datasheet

View All

COMMUNICATIONS MODULES & SUBSYSTEMS

10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder

PH1 Series

Key Features

• Three configurations supporting SR2/IR2/LR2 applications

• Supports dense wavelength division multiplexing

(DWDM) applications (without wavelocker)

• Microprocessor controls to support I2C

• Integrated 16:1/1:16 mux/demux

• Small form factor package (2.2" x 3.0" x 0.53") for high

density applications

• Low power consumption: 4.8 W typical, 6.8 W maximum

for TDM applications

• 70 °C maximum operating temperature

• High sensitivity PIN or APD receivers

• SONET, FEC, Ethernet and Multirate Capable Versions

• Forward, counter and line timing clocking modes

Applications

•

Telecommunications

Metropolitan Area Networks

Subscriber loop

Intra-office SONET/SDH

High bit-rate data communications

JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system

applications with reaches of up to 80 km. The series includes three different

transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM

applications. Each transponder accepts 16 bits of parallel digital data and converts

it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ

modulated optical signal and converts it into 16 bit wide parallel digital data.

The PH1 series offers low DC power dissipation and is available in either a small

form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53

inches) package, depending on system thermal performance requirements. The

transmit design uses an Electro-Absorptive Modulated Laser (EML) which,

depending on the configuration, produces an average output power of between

-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm

typical sensitivity) receiver is available, based on system configurations.

JDSU PH1 Series transponders are designed to support the following data rates:

9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),

10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.

Compliance

• Telcordia GR-253-Core

NORTH AMERICA

800 498-JDSU (5378)

WORLDWIDE

+800 5378-JDSU

WEBSITE

www.jdsu.com

Recommended Resources

Transistor attenuated tone control circuit

Single tuned IF amplifier circuit for radio

Switch circuit diagram triggered by finger

A control circuit that can both move and work for a long time

Photoelectric sensor light receiving circuit

Combustible gas alarm

Peregrine Programming Language - A Python-like language as fast as C: Hi everyone! My name is Ethan and I'm one of the 10 developers working on Peregrine. This post will go over some of the updates we've recently added to Peregrine.If you know Python, you know how easy ...; dcexpert MicroPython Open Source section

Xunwei 3399 development board Linux firmware compilation - install source code dependency package - compile Linux source code: 1. Install Linux source code dependency packagesIf you are using an Ubuntu16.04 virtual machine image with a compiled environment, the Linux source code dependency packages have already been installed...; 遥寄山川 ARM Technology

Can the signal tap in quarus ii copy multiple nodes: I have been using Xilinx's ISE for development before. When using chipscope to view waveforms, I can copy and regroup the probe signals, which is very convenient. Now I have just started using Quartus...; snowman3852 FPGA/CPLD

Pads 9.5 manufacturing problem inquiry: I want to make a component with a grounding copper foil under the CPU, but I don't want to remove the solder mask all over, and there is green paint solder mask on some parts. Is there a way to design...; bluemingchu PCB Design

My failed experience of cracking JLink: I ordered a version D of Jlink by mail, and tried to add a code to the upgraded .dll to read the contents of 0x00100000 flash, but it failed. I asked the seller for help, but he charged me for rewriti...; 黑衣人 Embedded System

Opinion: One of the often overlooked advantages of LED: Now most people already know that LED is a new light source for energy saving and emission reduction. But there is another great advantage that is often overlooked, that is, no pollution and environme...; 316966573 LED Zone

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components