DIP1987111182BB datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> DIP1987111182BB

DIP1987111182BB: DescriptionArray/Network Resistor, Bussed, 0.1W, 11800ohm, 100V, 0.1% +/-Tol, -15,15ppm/Cel, 7025,; CategoryPassive components The resistor; File Size334KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

DIP1987111182BB Overview

Array/Network Resistor, Bussed, 0.1W, 11800ohm, 100V, 0.1% +/-Tol, -15,15ppm/Cel, 7025,

DIP1987111182BB Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	791631362
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	6.9
structure	Welded
JESD-609 code	e4
Lead length	3.429 mm
lead spacing	2.54 mm
Network Type	Bussed
Number of terminals	14
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	2.032 mm
Package length	17.78 mm
Package form	DIP
Package width	6.35 mm
Rated power dissipation(P)	0.1 W
resistance	11800 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	1900
size code	7025
Temperature Coefficient	15 ppm/°C
Terminal surface	Gold (Au)
Tolerance	0.1%
Operating Voltage	100 V

DIP1987111182BB Preview

TaNFilm Precision DIP Network

Commercial and MIL Qualified

1900 Series

Inherent reliability

MIL-PRF-83401 qualified

Custom configuration available

Bonded leads not susceptible to

solder reflow problems

Absolute tolerance to

±0.1% / ratio tolerance to ±0.05%

Absolute TCR to

±15ppm/°C / ratio tracking to ±5ppm/°C



√

_____

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

How to ensure that the power supply works for a long time—ZDL oscilloscope recorder

STK0040II audio IC circuit diagram

Low cost fluorescent lamp electronic ballast circuit

Multi-channel power supply circuit diagram of digital camera using LT1308

555 variable delay lighting self-extinguishing circuit

875p computer motherboard circuit diagram_101

EEWORLD University ---- Toshiba Bluetooth IC: Toshiba Bluetooth IC : https://training.eeworld.com.cn/course/3708...; phantom7 RF/Wirelessly

Embedded Microprocessor Selection: The microprocessor used in embedded systems is very different from the microprocessor on a PC (personal computer), which is determined by the special characteristics of embedded systems. From the appl...; tkseo ARM Technology

AT89S51 watchdog program example: AJMP MAINMAIN: ;Start watchdog Mov 0A6H,#01EH ;Send 1E first Mov 0A6H,#0E1H ;Send E1 later ; Main program START: ACALL WDT ;Call reset watchdog subroutine AJMP START ;Main program ;Reset watchdog subr...; rain 51mcu

[TI's First Low Power Design Competition] Micro LCR Tester - Resistance Test and Accuracy Comparison: In this post, you will see the data of this small LCR testing resistors. Unfortunately, I am too busy at work, so this work may only be done to this step. There is still some calibration program left ...; snoweaglemcu Microcontroller MCU

Help, the serial port interrupt receiving data is incomplete: I use the STM3210B board to make a serial port program. I want to use the interrupt method to let USART1 send out characters after receiving them. After the program is completed, I find that when a st...; bluemaple stm32/stm8

Locating DSP illegal interrupts: I use eZdsp F2812 to write a program that use CpuTimer0 interrupt. This interrupt consists of many call function. This program is store in external memory since is a very long code. I encounter this e...; Jacktang Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components