WBC-T0303AS-03-1181-CD datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> WBC-T0303AS-03-1181-CD

WBC-T0303AS-03-1181-CD: DescriptionArray/Network Resistor, Center Tap, Thin Film, 0.25W, 1180ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 0303,; CategoryPassive components The resistor; File Size376KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

WBC-T0303AS-03-1181-CD Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 1180ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AS-03-1181-CD Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	802647757
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
resistance	1180 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBC(TAPPED)
size code	0303
technology	THIN FILM
Temperature Coefficient	25 ppm/°C
Tolerance	0.25%
Operating Voltage	100 V

Preview

Download Datasheet

View All

Wire Bondable

Chip Resistors

WBC Series

•

Discrete or tapped schematics

•

MIL inspection available

•

High resistor density

IRC Advanced Film Division

IRC’s WBC series wire bondable chip resistors are ideally suited for

the most demanding hybrid application. The WBC combines IRC’s

TaNSil

tantalum nitride thin ﬁlm technology with silicon substrate processing to produce an extremely small

footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil

resistor ﬁlm.

Available in a wide range of tolerances and temperature coefﬁcients to ﬁt a variety of hybrid circuit applica-

tions. Custom resistance values, sizes and schematics are available on request from the factory.

Physical Data

R0202 - Discrete

(0.508mm ±0.025)

0.020˝ ±0.001

Electrical Data

Absolute Tolerance

Absolute TCR

Package Power Rating

(@ 70°C)

Rated Operating Voltage

(not to exceed

√

P x R )

Operating Temperature

Back contact

Noise

Substrate Material

Top contact

Substrate Thickness

Aluminum

Gold

R0202 and

T0303

B0202

Passivation

to ±0.1%

to ±25ppm/°C

250mW

100V

-55°C to +150°C

<-30dB

Oxidized Silicon

(10KÅ SiO

min)

0.010˝ ±0.001

(0.254mm ±0.025)

10KÅ minimum

15KÅ minimum

Silicon

(Gold available)

Gold

3KÅ minimum

Silicon Dioxide or

Silicon Nitride

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

B0202 - Discrete back contact

(0.508mm ±0.025)

0.020˝ ±0.001

Top contact

pad chamfered

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

T0303 - Tapped network ½R + ½R

Bond Pad

Metallization

(0.762mm ±0.025)

0.030˝ ±0.001

Backside

½R

0.030˝ ±0.001

(0.762mm ±0.025)

0.004˝ min bond pad size

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com

A subsidiary of

TT electronics plc

WBC Series Issue April 2006

Recommended Resources

battery charger circuit

temperature control

Charge pump circuit principle The output current is I0 circuit diagram

Integrated chip protection circuit diagram

Negative reference voltage circuit

A collection of audio control circuits

2440 + Interrupt driver problem under CE5.0: I have done interrupt driver in 4.2, but I don't know how to do it in 5.0? Can anyone give me some guidance?...; kqyrabbit Embedded System

Do all voltage rails need to use low quiescent current? Here's the answer!: Almost all designers of ultra-low-power systems are concerned about battery life. How often does a fitness tracker battery need to be recharged? And for a disposable battery system, how often does a t...; qwqwqw2088 Analogue and Mixed Signal

Nand Flash read and write operation process: Can any expert explain the process of Nand Flash read and write operation? Mainly the page operation problem: bl ReadNandStatus ;Get the status result (stored in R1) mov r8, #0 ;r8 is set to 0, which ...; anglesccs Embedded System

Want to buy a set of electronic DIY electronic production tools: What are the generally needed DIY tools for slightly higher-end electronic production?...; xu__changhua DIY/Open Source Hardware

Never forget national humiliation: ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ...; dontium Talking

GPIO multiplexing: I have a newbie question. If I need to use a multiplexing function of GPIO, in addition to turning on the clock of the multiplexed peripheral, RCC_APB2Periph_AFIO clock, do I also need to turn on the ...; 123liuxiao stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components