EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S272AC-0140CDI

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size599KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

8N4S272AC-0140CDI Overview

LVDS Output Clock Oscillator

8N4S272AC-0140CDI Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1308556746
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TR
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability100%
Installation featuresSURFACE MOUNT
Nominal operating frequency133.333333 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry53/47 %
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S272
DATA SHEET
General Description
The IDT8N4S272 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
DNU 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
nOE 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S272CCD
REVISION A OCTOBER 3, 2012
1
©2012 Integrated Device Technology, Inc.
Graduation, give me some books
I don't want to move around, but I can't bear to throw them away. If any netizen needs them, I'll pay for the shipping and send them to you. If you need them, send me a private message.These three boo...
石玉 Buy&Sell
MPC8280 system clock
Is there a problem with selecting DEC for the mpc8280 system clock? The DEC interrupt priority is very low, not as high as the external interrupt. Can it be set?...
wangling47 NXP MCU
[Playing with LPC810 mini] Questions about systick
[i=s]This post was last edited by johnrey on 2015-7-15 21:56[/i] [color=#000][font=Tahoma,]Preconditions: 1. Systick is part of arm0+ core 2. In sleep mode, arm0+ core is down 3. __WFI will enter at l...
johnrey NXP MCU
Show off my ugly electronic load
Showing my ugly electronic load:) 1. Front view2. Back view: The heat sink has no insulation, so I cut it with an ABS machine, and the four corners are just right: lol3. Top view. This old case is ver...
dontium Microcontroller MCU
About the PWM output problem of MSP430G2553
The code in the picture below is to make P1.2 and P1.6 output PWM waveforms, but I don't understand the words in the red circle in the picture. Does it mean that P1.2 and P1.6 both output PWM with a d...
crysislove Microcontroller MCU
Please help explain the principle of this static eliminator
This machine is used for static elimination on plastic printing machines. It is made in Taiwan. The control board and thyristor are broken. The IC, thyristor and diode have all been polished. I have n...
ediy007 Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 316  1034  618  765  51  7  21  13  16  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号