EEWORLDEEWORLDEEWORLD

Part Number

Search

AX2200M25TR218X37

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 25V, 20% +Tol, 20% -Tol, 2200uF
CategoryPassive components    capacitor   
File Size176KB,1 Pages
ManufacturerIBS Electronics Inc
Download Datasheet Parametric View All

AX2200M25TR218X37 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 25V, 20% +Tol, 20% -Tol, 2200uF

AX2200M25TR218X37 Parametric

Parameter NameAttribute value
Objectid1218153205
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
capacitance2200 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
Custom functionsLead Length (Consult Factory)
diameter18 mm
dielectric materialsALUMINUM
length37 mm
Manufacturer's serial numberAX
negative tolerance20%
Number of terminals2
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package formAxial
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)25 V
seriesAX
Terminal pitch5 mm
6U CompactPCI
6U Low Power, Pentium-M Processor, Upgradable CPCI SBC Features: ? Supports 2 GHz Intel Pentium M processor ? 2MB L2 Cache ? Ultra-low power requirement, less than 12 W ? Supports up to 1 GB 200 MHz D...
wanglinwwy Embedded System
Why do I use int to declare variables when using EEPROM, but there are only 255 of them?
Why do I use int to declare variables when using EEPROM, but there are only 255 of them?...
ylf175300 51mcu
Power supply noise interference processing
一般而言,电源杂讯干扰的传播途径可分为下列二大类:??一、普通模式(Normal Mode):简称通模,指的就是二组输入电源线之间的杂讯。这些杂讯大多是由开关动作或者是静态功率转换器等干扰所造成,当这些干扰与正常讯号重叠在一起时,器材元件是无法分辨的,因为正常讯号也是以通模的状态存在。 ??二、共通模式(Common Mode):简称共模,指的是电源与接地之间的杂讯。这部分杂讯的起因多数是因为接地...
songbo Industrial Control Electronics
Principle of LED brightness control by microcontroller MCU
Microcontrollers MCU are usually considered digital devices. By default, their output voltage level is either high or low, not a neutral value. To achieve the requirement of LED brightness control, th...
火辣西米秀 Microcontroller MCU
Can the register secondary latch be latched correctly?
always@(posedge clk or negedge rst_n) begin ......... areg1<=a; areg2<=areg1; .... end assign a=~areg1& areg2;//High level is valid always@(posedge clk or negedge rst_n) begin ........... if(a) .........
1559638992 FPGA/CPLD
TI's BQ2057 charging current is only 200mA. Please give me some advice based on the picture above!
Using a 5V2A adapter, a lithium battery is fully charged to 4.1V, but the charging current is less than 200mA, the charging speed is too slow. See the picture, please improve...
ZHANGXU716 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1873  1238  357  773  1580  38  25  8  16  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号