EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-51-2GS4J1-18PNN

Description
Cable Assembly, 24AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-5-51-2GS4J1-18PNN Overview

Cable Assembly, 24AWG,

177-740-5-51-2GS4J1-18PNN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005107222
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.23
Other featuresSTANDARD: MIL-DTL-83513
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D FEMALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.205 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors51
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.093 Ω
shieldNO
stay19X36
Wire gauge24 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Huang Zhiwei from the University of South China A good system design is the guarantee for achieving good results in the competition
[i=s]This post was last edited by paulhyde on 2014-9-15 04:04[/i] [b]Huang Zhiwei, University of South China A good system design is the guarantee for achieving good results in the competition[/b]...
黄智伟 Electronics Design Contest
Wireless charging experiment
A paper on wireless charging experiment, very good~, there are specific circuits in it...
xtss RF/Wirelessly
Quartus II 8.0 installation problem
After I installed Quartus 8.0 (successfully cracked), I used its built-in IP generation tool to generate a three-speed Ethernet IP core and a simulation file. When I opened the simulation tool Questas...
eeleader-mcu FPGA/CPLD
About MOS tube recommendation
The 12VDC signal controls the on and off of the 24VDC relay. I want to use a MOS tube to drive it. Is there any economical and small MOS tube to recommend? If there is any other better solution, pleas...
xhd1099924128 Analog electronics
Can someone help me? About the 320F28035 clock problem
I am working on a DSP28035 chip, and the waveform is not correct when configuring the clock in the experiment. So I want to use DSP to control the TOPWAY LCD screen but it fails!DSP+12M crystal oscill...
huwei_harry Microcontroller MCU
Key points of welding, introduction of manual welding method
[i=s]This post was last edited by bjhyyq on 2017-7-19 11:35[/i] [align=left][size=14px][b]Preheating 1:[/b]Put the soldering tip in full contact with the solder joint. Figure 1 shows how to heat the s...
bjhyyq PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1548  1287  1480  826  2664  32  26  30  17  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号