EEWORLDEEWORLDEEWORLD

Part Number

Search

3GW14E-30T-FREQ

Description
LVCMOS Output Clock Oscillator, 200.1MHz Min, 800MHz Max, ROHS COMPLIANT PACKAGE-14/4
CategoryPassive components    oscillator   
File Size114KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GW14E-30T-FREQ Overview

LVCMOS Output Clock Oscillator, 200.1MHz Min, 800MHz Max, ROHS COMPLIANT PACKAGE-14/4

3GW14E-30T-FREQ Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Reach Compliance Codecompli
Maximum control voltage2.31 V
Minimum control voltage0.99 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate30 ppm
frequency stability50%
linearity10%
Installation featuresTHROUGH HOLE MOUNT
Maximum operating frequency800 MHz
Minimum operating frequency200.1 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVCMOS
Output load15 pF
physical size20.2mm x 12.8mm x 5.08mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
14 pin Dual-in-Line
Frequency range 200.1MHz to 800MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
DESCRIPTION
OUTLINE & DIMENSIONS
GW42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. GW42 VCXOs incorporate a high Q
fundamental crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption
<96MHz:
>96MHz:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GW14 VCXO
200.1MHz ~ 800.0MHz
200.1MHz to 800.0MHz
3.3 VDC ±5%
LVCMOS
2.6ps typical, 4.0ps maximum
(for 155.250MHz)
4.3ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
See table below
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
See table
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
30mA maximum (15pF load)
40mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (An
increase of control voltage
always increases output
frequency.)
-50° to +100°C
±5ppm per year maximum
Not available (4
pad package)
Fully compliant
PHASE NOISE
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-125dBc/Hz
-121dBc/Hz
-120dBc/Hz
-140dBc/Hz
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBERING
Example:
3GW14B-80N-250.00
Supply Voltage
3 = +3.3V
Series Designator
GW14
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
Regarding IAR path settings, recommended for novices
[backcolor=rgb(238, 238, 238)][font=Verdana, 宋体, sans-serif][size=12px]The project file is in E:\S3C2440\YS2440_IAR[/size][/font][/backcolor] [backcolor=rgb(238, 238, 238)][font=Verdana, 宋体, sans-seri...
什么鬼 Microcontroller MCU
Help design a simple 4ma to 20ma circuit diagram
I now have two 100 ohm resistors and a 1K variable resistor. A switch. I want to design a design that when the switch is closed, the voltage across the 100 ohms can be measured by a multimeter to be 0...
sunruiiris PCB Design
Fujitsu FRAM experience submission STM32 IO simulation driver RS64 always fails
Fujitsu FRAM experience submission STM32 IO simulation driver RS64 has always failed. Using the same program, only the chip select CS is different. The ID of W25X16 is correct, but there is a problem ...
upc_arm Integrated technical exchanges
Similarities and Differences between IMX6UL and IMX6ULL
[align=left][color=#333333][font=Arial][size=14px]Compared to i.MX6UltraLite, i.MX6ULL is mainly optimized for cost. It is PIN-2-PIN compatible with i.MX6UltraLite chip, making it easy to reuse i.MX6U...
maychen1991qz Embedded System
Active crystal oscillator output driving force
Dear experts, I have a question. The DSP used in the current project requires a 1.3V clock. I have a 3.3V crystal oscillator on hand, and use output voltage division to achieve 1.3V. The crystal oscil...
danielzhou Integrated technical exchanges
Help for
always @ (posedge clock) if(reset == 1) begin for(k=1; k<=order; k=k+1) Samples[k] <= 0; end else begin Samples[1] <= Data_in; for(k=2; k<=order; k=k+1) Samples[k] <= Samples[k-1]; end For the value o...
phdwong FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1868  401  1754  1827  2597  38  9  36  37  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号