Instruction Sheet
Dual In-Line Package (DIP)
Programming Switches
(7000 and 7100 Series)
408-7779
(was IS 7779)
04 MAY 06
Rev A
1. INTRODUCTION
NOTE
All dimensions are in metric units [with inches in
brackets]. Figures and illustrations are for
reference only, and are not drawn to scale.
This Instruction Sheet covers the installation of the
7000 and 7100 Series DIP Programming Switches
shown in Figures 1 and 2. Read this document before
performing any application using these products.
Low-Profile Switch
(Flush Rocker)
Standard Profile Switch
(Raised Rocker)
Rocker
PC Board
DIP Socket
Reason for revision may be found in Section 5,
REVISION SUMMARY.
Position Number
Tape
Low-Profile
Switch with
Side-Actuated Switch
(Side Rocker)
Application for Soldered Switch
Strippable
Transparent
Seal
Tape
Application for Removal Switch
SINGLE POLE SINGLE THROW (SPST)
RAISED ROCKER
SERIES AND
COLOR
NUMBER OF
POSITIONS
Unsealed
Econ. Seal
Unsealed
Econ. Seal
Unsealed
Econ. Seal
(STANDARD-PROFILE)
SIDE ROCKER
(SIDE-ACTUATED)
FLUSH ROCKER
(LOW-PROFILE)
2
3
4
5
7000 Black
(Refer to
Product Spec
108-7519)
6
7
8
9
10
11
12
2
3
4
5
7100 Blue
(Refer to
Product Spec
108-7532)
6
7
8
9
10
11
12
2-435166-9
3-435166-0
435166-2
435166-3
435166-4
435166-1
435166-5
435166-6
435166-7
---
3-435166-2
2-435640-9
3-435640-0
435640-2
435640-3
435640-4
435640-1
435640-5
435640-6
435640-7
---
3-435640-2
---
---
4-435166-9
5-435166-0
5-435166-1
5-435166-2
5-435166-3
5-435166-4
5-435166-5
---
5-435166-7
---
---
3-435640-5
3-435640-6
3-435640-7
3-435640-8
3-435640-9
4-435640-0
4-435640-1
---
4-435640-3
1-435802-0
435802-2
435802-3
435802-4
435802-5
435802-6
435802-1
435802-7
435802-8
---
1-435802-2
---
---
---
---
---
---
---
---
---
---
---
---
---
1-435802-5
1-435802-6
1-435802-7
1-435802-8
435802-9
1-435802-9
2-435802-0
2-435802-1
2-435802-2
---
---
---
---
---
---
---
---
---
---
---
---
---
435626-1
435626-2
---
---
435626-5
---
---
---
---
435668-1
435668-2
435668-3
435668-4
435668-5
435668-6
435668-7
---
435668-9
---
1-435668-1
3-435626-6
3-435626-7
3-435626-8
3-435626-9
4-435626-0
4-435626-1
4-435626-2
4-435626-3
4-435626-4
---
4-435626-6
2-435668-6
3-435668-3
3-435668-4
3-435668-5
2-435668-5
2-435668-7
2-435668-8
2-435668-9
3-435668-0
3-435668-1
3-435668-2
NOTE: Contact Tyco Electronics for RoHS compliant part numbers which may be associated with this document.
Figure 1
E
2006 Tyco Electronics Corporation, Harrisburg, PA
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
1
of 4
LOC B
All International Rights Reserved
Tyco is a trademark.
*Trademark
Other products, logos, and company names used are the property of their respective owners.
DIP Switches (7000 and 7100 Series)
408-7779
2. INTRODUCTION
3. SWITCH INSTALLATION
The SPST and MPMT switches are available in 2
through 12 positions. They can be used in DIP
sockets with in–row contact centerline spacing of 25.4
[.100] and row–to–row contact centerline spacing of
7.62 [.300], or they can be soldered directly to the
printed circuit (pc) board.
There are standard–profile, side–actuated, and low–
profile SPST switches. The standard–profile switches
have raised rockers, and are available unsealed, or
sealed with an economy or premium masking
material. The side–actuated switches have rockers on
the side rather than on the top, and are available
unsealed, or sealed with an economy or premium
masking material. The low–profile switches have flush
rockers, and are available unsealed, or sealed with an
economy clear tape, or sealed with a premium
masking material.
There are standard–profile and side–actuated MPMT
switches. The standard–profile MPMT comes in both
Single–Pole Double–Throw (SPDT) and Double–Pole
Double–Throw (DPDT) make–before–break switches
and are available with a low–profile and extended
lever actuator. The side–actuated MPMT is available
in SPST only at this time. All of these switches are
available in the unsealed version only.
The unsealed switches are designed for socket
applications and the sealed are designed for soldering
applications directly to the pc board. The sealants
prevent flux and other contaminants from entering the
switch during soldering and cleaning.
Determine the number of switch positions required for
your application. Determine whether the switch will be
soldered directly to the pc board ( a sealed switch will
be required), or whether the switch is to be installed in
a socket (an unsealed switch can be used). Refer to
the tables in Figures 1 or 2 for assistance in selecting
a switch.
3.1. DIP Socket Installation
1. Secure DIP socket to pc board according to
instructions packaged with socket.
2. Start one row of contact leads into one row of
contact cavities in socket, then rotate switch until it
is parallel with socket.
3. Gripping ends of switch, push switch into socket
until it is bottomed
4. Determine which of the circuits are to be closed,
then depress the applicable rockers to the ON
position.
5. If installing a protective dust cover, determine
the number of switch positions and refer to
Customer Drawing 435238 to select the applicable
cover. Check to be sure there are no obstructions
on the switch rockers or in the protective cover,
then slide the cover over the rockers until the cover
latches engage the housing. See Figure 3.
MULTIPLE THROW MULTIPLE THROW SWITCHES (MPMT)
DOUBLE POLE SINGLE THROW
Low Profile Actuator
Extended Actuator
SINGLE POLE DOUBLE THROW
Low Profile Actuator
Extended Actuator
SERIES AND
COLOR
CO O
NUMBER OF
SWITCHES
S
C
S
1
2
7000 Black
(Refer to
Product Spec
S
108 7519)
108-7519)
5
6
3
4
435469-9
---
435469-2
435469-3
---
1-435469-0
2-435469-1
2-435469-2
2-435469-3
2-435469-4
2-435469-5
2-435469-6
435470-7
435470-1
435470-2
435470-3
435470-4
435470-8
2-435470-1
2-435470-2
---
2-435470-4
2-435470-5
2-435470-6
SERIES AND
COLOR
CO O
NUMBER OF
SWITCHES
S
C
S
FOUR POLE SINGLE THROW
Low Profile Actuator
Extended Actuator
DOUBLE POLE DOUBLE THROW
Low Profile Actuator
Extended Actuator
7000 Black
(Refer to
Product Spec
p
108-7519)
1
2
3
435469-7
---
---
3-435469-1
3-435469-2
---
435470-5
435470-9
---
3-435470-1
3-435470-2
3-435470-3
Figure 2
2
of 4
Rev
A
DIP Switches (7000 and 7100 Series)
408-7779
Protective Cover
Grip Here
Housing Bottomed
on PC Board
PC Board
Clinched Contact Lead (Inward Only)
Figure 5
Cover Latch
NOTE
For pc board soldering and cleaning procedures,
and recommended solvents, refer to Tyco
Figure 3
Electronics Application Specification 114-1056.
3.2. PC Board Installation
4. SWITCH PROGRAMMING
1. Make a layout on the pc board according to the
dimensions shown in Figure 4.
2. Make certain all contact leads have started entry
into holes. Grip sides of switch and push switch
into pc board until it is bottomed.
3. Hold switch at a slight angle and start one row
on contact leads into pc board holes. Do NOT
over–insert. Switch should be rotated until second
row of contact leads are aligned with opposite row
of contact holes.
Use Light Pressure
to Insert Switch
After the switch has been inserted into the DIP socket
or soldered onto the pc board, proceed as follows:
1. Remove seal from the switches, see Figure 6.
Remove Tape
Seal from
End
Low-Profile Switch
Rotate to Align Second
Row - Then Push Down
on Ends of Switch
Remove Seal from Top
7.62 [.300] Ref
Left to Bottom Right
(Diagonal Across the
Switch)
Masking Material
Seal
NOTE: These same procedures
2.54 [.100] Ref
apply to socket installation.
Figure 4
NOTE
To hold switch in place during wave soldering, the
four outside contact leads may be clinched
inward at 45 . Refer to Figure 5.
Standard-Profile or
Side-Actuated Switch
°
Figure 6
Rev
A
3
of 4
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
