Features ....................................................................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
Revision History ......................................................................................................................................................................... 15
Rev 1.09
Page 3 of 16
www.sitime.com
SiT9366
1 MHz to 220 MHz Ultra-low Jitter Differential Oscillator
Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with standard
output termination show in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 2. Electrical Characteristics – Common to LVPECL, Low-swing LVPECL, LVDS and HCSL
(All
temperature ranges)
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-10
-20
-25
-50
First Year Aging
5 Year Aging
10 Year Aging
20 Year Aging
Operating Temperature Range
F_1y
F_5y
F_10y
F_20y
T_use
-0.7
-1.1
-1.3
-1.5
-20
-40
-40
-40
Supply Voltage
Vdd
2.97
2.70
2.52
2.25
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Startup Time
OE Enable/Disable Time
VIH
VIL
Z_in
DC
T_start
T_oe
70%
–
–
45
–
–
Typ.
–
–
–
–
–
±0.4
±0.7
±0.8
±1.0
–
–
–
–
3.30
3.00
2.80
2.50
–
–
100
–
–
–
Max.
220.000001
+10
+20
+25
+50
+0.7
+1.1
+1.3
+1.5
+70
+85
+95
+105
Supply Voltage
3.63
3.30
3.08
2.75
–
30%
-
55
3.0
3.8
V
V
V
V
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value.
f = 156.25 MHz. Measured from the time OE pin reaches rated
VIH and VIL to the time clock pins reach 90% of swing and
high-Z. See
Figure 8
and
Figure 9.
Pin 1, OE
Pin 1, OE
Pin 1, OE logic high or logic low
Unit
MHz
ppm
ppm
ppm
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
°C
Extended Industrial
At 85°C
At 85°C
At 85°C
At 85°C
Extended Commercial
Industrial
Condition
Accurate to 6 decimal places
Inclusive of initial tolerance, operating temperature, rated power
supply voltage and load variations
Frequency Range
Frequency Stability
Temperature Range
Input Characteristics
Output Characteristics
Startup and OE Timing
Rev 1.09
Page 4 of 16
www.sitime.com
SiT9366
1 MHz to 220 MHz Ultra-low Jitter Differential Oscillator
A. Selection of inverter brand:Don't just look at the price. Some inverters are cheap, but the quality and performance are extremely poor. They cut corners, have a short lifespan, few accessories, and...
A small example of single-chip program performance optimizationI haven't played with 51 for a long time. Yesterday I helped someone look at a dot matrix screen program. The screen is 64*16, using 2 13...
[color=#000][backcolor=rgb(232, 232, 232)][size=15px]Hello masters, I have some problems when displaying dynamic curves, as follows: [/size][/backcolor][/color] [color=#000][backcolor=rgb(232, 232, 23...
I'm trying to connect a USB (HID) device to Linux and write data to the device. I want to find a tool that can see the data exchange. I hope someone can recommend one to me!...
A comprehensive introduction to isolation in electronic circuits: Isolation between analog and digital (serial 5) Author: Beijing jerrymiao Generally speaking, the conversion between analog circuits a...
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
The emergence and development of street lamps are inseparable from the prosperity and progress of cities, which makes street lamps useful. Conversely, street lamps also make the night of the city n...[Details]
1. The composition and structure of mobile phone lithium battery
Mobile phone lithium batteries are mainly composed of plastic shell upper and lower covers, lithium battery cells, protection c...[Details]
Rated capacity refers to the maximum output power of the UPS (the product of voltage V and current A).
Usually, the UPS power supplies sold on the market are marked with "W" (watt) for smaller...[Details]
Dual Tone MultiFrequency (DTMF) signaling is gradually being used in push-button telephones around the world. It quickly replaced the dial pulse signaling used in traditional rotary phones because ...[Details]
Industrial Control Electronics
京公网安备 11010802033920号
EEWORLD
