GUB-GL8ALF-03-3050-B- datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> GUB-GL8ALF-03-3050-B-

GUB-GL8ALF-03-3050-B-: DescriptionArray/Network Resistor, Isolated, Thin Film, 0.16W, 305ohm, 0.1% +/-Tol, -25,25ppm/Cel, 4430,; CategoryPassive components The resistor; File Size493KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

GUB-GL8ALF-03-3050-B- Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 305ohm, 0.1% +/-Tol, -25,25ppm/Cel, 4430,

GUB-GL8ALF-03-3050-B- Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	795610682
package instruction	SMT, 4430
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	7.2
structure	Molded
JESD-609 code	e3
Network Type	Isolated
Number of terminals	16
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	2.667 mm
Package length	11.176 mm
Package form	SMT
Package width	7.544 mm
Rated power dissipation(P)	0.16 W
resistance	305 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	GUB
size code	4430
technology	THIN FILM
Temperature Coefficient	25 ppm/°C
Terminal surface	Matte Tin (Sn)
Tolerance	0.1%

Preview

Download Datasheet

View All

TaNFilm

Small Outline Surface

Mount Resistor Network

GUB Series

•

Thin ﬁlm on ceramic technology

0.220” and 0.300” sizes available

RoHS compliant version available

DESC 87012 and 87013 available

Standard JEDEC packages for automatic placement equipment

Compliant leads to

compensate for

thermal expansion

and contractions.

IRC Advanced Film Division

Ultra precision tantalum

nitride resistance element

on high purity alumina.

Rugged, molded

construction.

IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.

The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor

cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each

lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed

created by soldering and temperature excursions.

The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.

TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance

exceeding MIL-PRF-83401 characteristics H.

Electrical Data

GM Type

Resistance Range (Ω)

GL Type

Absolute Tolerance

Ratio Tolerance To R1

TCR (ppm/°C)

TCR Tracking To R1 (ppm°C)

Operating Temperature Range

Noise

Substrate

Custom circuits and special testing available.

Schem A: 10 to 200K

Schem B: 10 to 1000K

Schem A: 10 to 150K

Schem B: 10 to 75K

Available to ±0.1%

Available to ±0.05%

±25, ±50, ±100

±5

-55°C to +125°C

Less than -25 dB

High purity alumina substrate

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• 4222 South Staples Street • Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com

A subsidiary of

TT electronics plc

GUB Series Issue November 2008 Sheet 1 of 3

Recommended Resources

Loom power saving automatic switch circuit

Use NE555 to make light-controlled flashing warning lights

Otto QB4 soft starter starts one motor circuit

Two types of light-controlled relay circuit diagrams

Non-polar electrolytic capacitor aging circuit

Computer motherboard circuit diagram 810 4_15

How to build a cross-compilation environment for PXA270: I bought a book called "ARM Embedded from Beginner to Mastery", in which the second chapter contains content about building a cross-compilation environment step by step. However, I always make mistake...; krg07 Embedded System

About the I/O port space addressing problem of TMS320VC5402: What is the correspondence between the addressing of the I/O port space of DSP5402 and the external parallel I/O pins?...; chinalee1990 DSP and ARM Processors

My ZLG M0 is probably in trouble.: Today, I was happily adjusting the PWM program and when the oscilloscope probe touched the pin, there seemed to be some sparks. I didn't pay much attention to it. The waveform appeared, but the freque...; 常见泽1 NXP MCU

The PCB I drew today was despised. Who can take a look?: 1 I spent a lot of effort to design a FPGA PCB. I showed it to my classmates. They said three things about the board, saying that it was too bad and that the board I drew was too bad. (I held back at ...; 江汉大学南瓜 PCB Design

Xilinx simulation can be realized, but the memory chip cannot be burned into it: The XC3S500E chip can be simulated, but the memory chip XCF04S cannot be burned in and Verify fails. Thank you for your guidance....; museum FPGA/CPLD

Problem with BIOS\"task\" object.: I would like to ask you:In BIOS, I use TSK0 to call the function test(), and the hardware interrupt INT1 calls T0ISR(). After running the program, the program always enters T0ISR() without calling the...; fangyu_99 Analogue and Mixed Signal

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components