The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts absorb on the top
tapes to cause a failure in the mounting and the parts are destructed by static electricity (more than 1kV : 1J, 2A, 2B, 2E 0.5kV : 1E, Human Body Model 100pF 1.5kΩ) to change the
resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged on the tapes. Similarly, care should be given not to apply the
excessive static electricity when mounting on the boards.
●
Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc. The flux may
contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na
＋
), chrorine (Cl
−
) etc. Therefore these kinds of ionic substances may
induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since lead free solder contains ionic substances.
Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk may happen that
the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of protecting coat may be dropped down.
Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling strength. 5∼
35℃/35∼75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like hydrogen sulfide, sulfurous acid
gas, hydrogen chloride, etc. may drop solderability.
Recently I am working on communication between two GPRS modems. When one modem sends a short message or MMS, what message response can the other modem receive after receiving the message/MMS? How can ...
If you need it, please contact me. The deadline for free service is 2009.6.28 (I have no time because I am at work) [[i] This post was last edited by sjl105105 on 2009-6-26 12:41 [/i]]...
The original IAR5.3 project was moved to 6.3, compiling, 0 errors, 0 warnings. Problems occurred during linking, e183: Static overlay map generation (-xo) is not supported for MSP430 processor,,, the ...
I would like to ask the experts in the forum: Is there any good way to realize video transmission on winmobile system? I have only done video transmission on windows, and now I need to realize video a...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
As countries around the world are leaning towards the new energy battery industry, lithium-ion power batteries, as the ideal energy source for the development of the 21st century, are attracting mo...[Details]
Introduction
The LED market has seen tremendous growth over the past few years. Advances in thermal dissipation, packaging, and processing have resulted in higher brightness, higher efficien...[Details]
Do you have the basic terms of optics memorized? If not, read here.
Correlated Color Temperature: If the color of light emitted by a light source is closest to the color of light radiate...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
