EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-10601211BA

Description
Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

51760-10601211BA Overview

Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle

51760-10601211BA Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid307847829
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsHOLE .086-.098
body width0.47 inch
subject depth0.82 inch
body length5.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN/LEAD
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED POLYETHYLENE
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
The STM8 library is a redundant thing
I downloaded the STM8 library these two days and followed some instructions to add what should be added. There is an interrupt. I remember it is STM8-interrupt-vector.c. It is always automatically add...
ddllxxrr stm32/stm8
I would like to ask a question: should the ADC driver be closer or farther away from the ADC?
[i=s]This post was last edited by littleshrimp on 2015-12-9 11:46[/i] Should the ADC driver in the figure be placed closer to the signal input terminal on the left or closer to the ADC on the right? I...
littleshrimp Analog electronics
My opinion on SDRAM (reprinted)
In the past week, I used the EP1C3T144C8 FPGA to embed NIOS2 and studied the drivers of FLASH and SDRAM. Finally, it was easy to use, but I encountered many twists and turns in the process. Now I will...
FPGA小牛 FPGA/CPLD
Help, can the I2C rate of STM32F103 be reduced to below 5K?
As the title says, the crystal oscillator uses 8MHz...
123456ZJ stm32/stm8
Assembly language instruction DA
What is the function of the DA instruction, when is it generally used, and how to use it specifically? The book and many materials only briefly mention it....
zjjone1023 51mcu
G2553 uses i2c mode
使用GPIO读写eeprom没问题后想学习I2C mode下了TI的SLAA208c范例來调适其中 void EEPROM_ByteWrite(unsigned int Address, unsigned char Data) {unsigned char adr_hi;unsigned char adr_lo;while (UCB0STAT & UCBUSY);// wait until I2C...
jk4857 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2350  1527  2252  860  1793  48  31  46  18  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号