Anti-surge chip resistors
ESR series
●
Datasheet
Features
1)Exclusive resistive element pattern and laser trimming technology results in
significantly improved surge resistance characteristics.
2)2kV to 5kV electrostatic discharge resistance.
3)Superior power ratings.
4)ROHM resistors have obtained ISO9001 / IATF16949 certification.
5)Corresponds to AEC-Q200.
●
Products list
Size
(mm)
Rated
power
(70
℃
)
(inch)
(W)
Limiting
element
voltage
(V)
T
emperature
coefficient
(ppm /
℃
)
±100
±100
+500/-250
±200
±100
±200
±100
±200
±100
±100
±200
±100
±100
±200
±100
±100
±200
Resistance
tolerance
(%)
F ( ±1% )
F ( ±1% )
J ( ±5% )
J ( ±5% )
D ( ±0.5% )
F ( ±1% )
F ( ±1% )
J ( ±5% )
D ( ±0.5% )
F ( ±1% )
J ( ±5% )
D ( ±0.5% )
F ( ±1% )
J ( ±5% )
D ( ±0.5% )
F ( ±1% )
J ( ±5% )
Resistance range
(Ω)
10
≦
R
≦
976k (E24/96 series)
1M
≦
R
≦
2.2M (E24 series)
1
≦
R
≦
9.1 (E24 series)
10
≦
R
≦
10M (E24 series)
10
≦
R
≦
1M (E24/96 series)
1
≦
R<10
(E24/96 series)
10
≦
R
≦
10M (E24/96 series)
1
≦
R
≦
10M (E24 series)
10
≦
R
≦
1M (E24/96 series)
1
≦
R
≦
10M (E24/96 series)
1
≦
R
≦
10M (E24 series)
10
≦
R
≦
1M (E24/96 series)
1
≦
R
≦
10M (E24/96 series)
1
≦
R
≦
10M (E24 series)
10
≦
R
≦
1M (E24/96 series)
1
≦
R
≦
10M (E24/96 series)
1
≦
R
≦
10M (E24 series)
Operating
temperature
range
(
℃
)
Automotive
grade
available
Part No.
ESR01
1005
0402
0.20
50
-55
½
+155
Yes
ESR03
1608
0603
0.25
150
-55
½
+155
Yes
ESR10
2012
0805
0.40
150
-55
½
+155
Yes
ESR18
3216
1206
0.5
200
-55
½
+155
Yes
ESR25
3225
1210
0.66
200
-55
½
+155
Yes
* Design and specifications are subject to change without notice.
Carefully check the specification sheet supplied with the product before using or ordering it.
* E24 : Standard products, E96 : Custom products.
●
Part Number Description
E S R
Part No.
ESR
(Anti-surge
chip resistors)
1 0
Size
(mm [inch])
01(1005 [0402])
03(1608 [0603])
10(2012 [0805])
18(3216 [1206])
25(3225 [1210])
EZ P
Packaging specifications code
Packaging
Part No. Code specifications Quantity
/ Reel
ESR01
ESR03
ESR10
ESR18
ESR25
J
Resistance
tolerance
D ( ±0.5% )
F ( ±1% )
J ( ±5% )
EX.)
1 0 0
Nominal resistance
Resistance code, 3 or 4 digits.
Resistance
tolerance
D,F
J
：
：
MZP
EZP
EZP
EZP
JZP
Paper tape
( 2mm Pitch)
Paper tape
( 4mm Pitch)
Paper tape
( 4mm Pitch)
Paper tape
( 4mm Pitch)
Embossed tape
( 4mm Pitch)
10,000
5,000
5,000
5,000
4,000
Resistance
code
4 digits
3 digits
1Ω = 1R00 (±1%)
1R0 (±5%)
10Ω = 10R0 (±0.5%,±1%)
100 (±5%)
1MΩ = 1004 (±0.5%,± 1%)
105 (±5%)
www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved.
1/4
2020.07 - Rev.J
ESR series
●
Datasheet
Derating curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curve below.
■
ESR 01 / 03 / 10 / 18 / 25
●
Characteristics
T items
est
Guaranteed Value
See P
.1
See P
.1
20
℃
Measurement
：
+25/-55, +25/+125
℃
T voltage is the smaller one of
①
or
②
est
①
Rated voltage(current)×2.5,(ESR03/10/18/25) 2s
Rated voltage(current)×2.0,(ESR01) 2s
②
Maximum overload voltage
※
Rosin-ethanol solution(25% mass)
Soldering condition
：
245±5
℃
Duration of immersion
：
2.0±0.5s
Soldering condition
：
260±5
℃
Duration of immersion
：
10±1s
T temp
：
-55
℃½
+125
℃
5cycles
est
40
℃，
93
％
(Relative humidity)
T time
：
1,000h
est
Rated voltage(current),70
℃
1.5h:ON
－
0.5h:OFF
T time
：
1,000h
est
155
℃
T time
：
1000h
est
23±5
℃
_E0057
Solvent: 2-propanol
-
EIAJ ED-4701/300 T method 304
est
Voltage
：
2kV(ESR01)
3kV(ESR03/10/18)
5kV(ESR25)
C
：
100pF
R
：
1.5kΩ
Apply cycle
：
Once
Compliance Standard(s) : IEC60115-8
T conditions
est
Resistance
Variation of resistance
with temperature
Overload
±(2.0
％＋
0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed and
no soldering damage.
±(1.0
％＋
0.05Ω)
No remarkable abnormality on the appearance.
±(1.0
％＋
0.05Ω)
±(3.0
％＋
0.1Ω)
±(3.0
％＋
0.1Ω)
±(3.0
％＋
0.1Ω)
±(1.0
％＋
0.05Ω)
±(1.0
％＋
0.05Ω)
Without mechanical damage such as breaks.
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Endurance at 70
℃
Endurance
Resistance to solvent
Bend strength of
the end face plating
Static
electric
characteristics
±(5.0
％＋
0.05Ω)
※
Maximum overload voltage (T voltage)
est
ESR01
100V
ESR03
200V
ESR10
200V
ESR18
400V
ESR25
400V
www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved.
3/4
2020.07 - Rev.J
Notice
Precaution on using ROHM Products
1.
If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
(Note 1)
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl
2
,
H
2
S, NH
3
, SO
2
, and NO
2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
The Products are not subject to radiation-proof design.
Please verify and confirm characteristics of the final or mounted products in using the Products.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
Confirm that operation temperature is within the specified range described in the product specification.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
3.
4.
5.
6.
7.
8.
9.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
2.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.004
Linux and Android
京公网安备 11010802033920号
EEWORLD
