The Model 20SW is a high accuracy Industrial ASIC Pressure Switch,
designed for use in a variety of applications. Applying digital
compensation, this product offers top performance over a wide
temperature range. Utilizing Krystal Bond Technology™, the sensing
element will measure pressure in the most extreme temperature
conditions.
Where other sensor technologies will freeze or boil, the 20SW uses a
one piece stainless steel sensor to offer continuous operation. If
linearity and repeatability are critical for your application, this product
will exceed your expectations at an affordable price.
Benefits
ASIC Compensation
Superb Temperature Performance
Excellent Accuracy
Factory Sealed
Wide Operating Temperature Range
High Proof and Burst Pressure
Hydraulics Controls
Boilers
Marine
Applications
Railways
SENSOR SOLUTIONS
/// AST20SW
06/2017
Page 1
STAINLESS STEEL
AST20SW SPDT Pressure Switch
Performance @ 25°C (77°F)
Error Tolerance
Over Range
Protection
Burst Pressure
Pressure Cycles
< ±0.1% BFSL of line pressure
2X Rated Pressure, standard
(For higher proof pressures, contact factory)
5X or 60,000PSI of line pressure, whichever is less
> 100 million full pressure cycle
Environmental Data
Temperature
Operating
Storage
-40 to 85°C (-40 to 185°F)
-50 to 105°C (-58 to 221°F)
0-100% relative humidity, non-condensing
Thermal Limits
Compensated Range
-20-70°C (-4 to 158°F)
Other
Shock
Vibration
EMI/RFI Protection:
Rating:
100G, 11 msec, 1/2 sine
10G peak, 20 to 2000 Hz.
Yes
IP-66
Electrical Data
Excitation
Current Consumption:
Set Point
Output Load:
Reverse Polarity
Protection
10-28VDC
< 10mA
See Chart
1 Amp, Resistive
Yes
SENSOR SOLUTIONS
/// AST20SW
06/2017
Page 2
STAINLESS STEEL
AST20SW SPDT Pressure Switch
Dimensions
SENSOR SOLUTIONS
/// AST20SW
06/2017
Page 3
STAINLESS STEEL
AST20SW SPDT Pressure Switch
Ordering Information
AST20SW
Series Type
Process Connection*
A= 1/4"-18 Male NPT C= 1/4"BSPP
B= 1/8"-27 Male NPT W= F250C Female Autoclave
System Pressure
Insert 2 digit code
50
100
250
01
02
03
04
05
06
07
08
09
10
A
05
P
E
Y
1
G
00025
F
05
000
System Pressure
500
3000
5000
7500
10,000
15,000
20,000
11
consult factory for pressures not shown
Pressure Unit
P= PSI
Switch Configurations
E= SPDT [Form C]
Electrical Connection
Y= M12x1
Wetted Material**
0= 17-4PH
1= 316L
2= Inconel 718
G= Vented Gauge Pressure
Pressure Reference
Number (0, 1, 2)= Sealed Gauge
Switching Point Pressure
Insert 5 digit code [5-95% of system line pressure]
25
00025
50
00050
100
00100
250
00250
500
00500
1,000
01000
2,500
02500
5,000
05000
10,000
10000
consult factory for pressures not shown
Switching Pressure
Switching Direction
F= Falling
R= Rising
Hysteresis:
Insert 2 digit code (example: 1% is 01) [1% of line pressure minimum]
Options= 000
*For optional pressure ports and electrical interfaces please consult factory. 1/8” NPT Male not available under 50PSI or with
316L. F250C Female Autoclave is the only option for 10,000 to 20,000PSI, not available in 316L. **316L available up to
10,000 PSI. For Inconel 718 consult factory on availability.
NORTH AMERICA
American Sensor Technologies, Inc. (AST),
a TE Connectivity Company
Tel: 800-522-6752
Email:
customercare.molive@te.com
Code
Code
1000
ASIA
Hong Kong Sensor Technologies (HKST),
a TE Connectivity Company
Tel: 0400-820-6015
Email:
customercare.shzn@te.com
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to
herein might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or
misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
RTC interrupt requests the kernel interrupt via EXTI_17, but in the 3.3 version of the firmware library, the RTC routine does not configure EXTI17 to enable, but only allows NVIC_RTC and RTC interrupt...
Audio input and output problems are often encountered in embedded product development. How to add "speaker" and "microphone" devices to them? This article will briefly introduce the audio solution in ...
When I came back yesterday evening and opened the door, I could smell the smell of burning liquid gas. It was not very light. It was strange. I was a little panicked at that time (after all, it was no...
Job requirements: 1. Bachelor degree or above, major in communications, electronics, automation, computer or related, more than five years of work experience; 2. Engaged in hardware development for ma...
[i=s]This post was last edited by dontium on 2015-1-23 13:07[/i]LED-TPS6116x with independent power stage and IC input voltageMSP430 connects to TPS60250 via I2C master software...
**, Hello: Xiaoming. Male. Born on July 40, 1986. Height 190, weight 80KG. Native place: Jinan, Shandong Province. Believes in atheism and power worship. Good health. Unmarried. Hobbies: computer, gui...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
