EEWORLDEEWORLDEEWORLD

Part Number

Search

SP-200.82OHM5%LF

Description
Fixed Resistor, Wire Wound, 1W, 0.82ohm, 5% +/-Tol, 800ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size224KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

SP-200.82OHM5%LF Overview

Fixed Resistor, Wire Wound, 1W, 0.82ohm, 5% +/-Tol, 800ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

SP-200.82OHM5%LF Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1727885682
package instructionAXIAL LEADED, ROHS COMPLIANT
Reach Compliance Codecompliant
ECCN codeEAR99
JESD-609 codee3
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature160 °C
Package shapeTUBULAR PACKAGE
Rated power dissipation(P)1 W
Rated temperature50 °C
resistance0.82 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient800 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeWIRE
Tolerance5%
General Purpose Failsafe
Molded Wirewound Resistor
SP20/SP20F Series
SP20F Fusible
±5%, ±10% tolerance
0.1 ohm to 1200 ohms
F version has flame resistant coating
1 watt rated with 1/2 watt dimensions
Drop-in replacement for BW20/BW20F
Weldable and solderable magnetic lead
TCR’s as low as ±150 ppm/°C standard (custom TC’s available)
Lead free, RoHS compliant construction available
3
1
4
2
(See notes below)
Electrical Data
IRC Type
SP20
SP20F
1. Resistive Element
All resistor types have resistance alloy
winding on a braided fiberglass substrate.
Intermediate silicone coatings are used
to enhance processibility and to provide
protection to the resistive element.
2. Termination
The SP-20 and SP-20F resistors are
terminated using an alloy coated copper
flashed steel lead welded to a cap of the
same material. This termination assembly is
mechanically crimped, utilizing an improved
crimp design, to the resistive element.
3. Encapsulation
The SP-20 and the SP20F are encapsulated
utilizing a compression molded phenolic
plastic material. The SP-20F has a flame
resistance coating applied over the resistive
element to provide flammability protection
when destructive overloads may occur.
4. Marking
All products are marked utilizing heat and
solvent resistant color code bands consistent
with EIA/MIL requirements. The first band
is double width to designate wirewound
construction. A fifth band, blue in color, is
used for flameproof identification.
EIA RS-344 Style
MIL-R-11 Style
Resistance - Std.
Tolerance - Std.
CRU1
RC20/RC32
0.1Ω to 1200Ω
±5%, ±10%
CRU1
RC20/RC32
0.1Ω to 1000Ω
±5%, ±10%
Power Rating
1 watt @ 50°C
1 watt @ 50°C
3/4 watt @ 70°C
3/4 watt @ 70°C
---
1/2 watt @ 100°C
Derating to 0 @ 160°C Derating to 0 @ 160°C
Max. Continuous Working Voltage
Min. Insulation
Resistance
Min. Dielectric
Withstanding Volts
(RMS)
Reduced Pressure
Dry
Wet
ATM
PR
10,000 Meg
100 Meg
700V
450V
120°C @ 1 watts
5%
Negligible
PR
10,000 Meg
100 Meg
700V
450V
120°C @ 1 watts
5%
Negligible
Hotspot Temperature Rise
Typical Load Life
Current Noise
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
SP20/SP20F Series Issue December 2008 Sheet 1 of 3
Analysis example of winning entries from the International Chaos C Language Competition
The results of the International Chaotic C Language Competition are undoubtedly the result of the world's top C programmers' extreme exploration of the C language. Reading and analyzing them is defini...
呱呱 MCU
What is a low impedance path? Please explain it in detail.
What is a low impedance path? Please explain it in detail....
mq13947193109 Embedded System
Please help me look at my counting program
[i=s]This post was last edited by paulhyde on 2014-9-15 09:50[/i] ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;Pulse counting program, used to count the number of pulses in one minute; ... ; Divid...
feiji11 Electronics Design Contest
I made a USB to serial port using pl2303, but the computer can't detect it.
I made a USB to serial port with pl2303, but the computer can't detect it. Only when I connect the multimeter to pin 17 and ground, the computer can detect it. I have been looking for several days, pl...
yinshulong Embedded System
Exercises I wrote when I was learning C (1) -------Throw it up to ask for rotten eggs.......
I recently reinstalled my computer and almost lost the exercises and some materials I had accumulated over the years. Recently , I have a new view on cleaning up my own materials: everything should be...
辛昕 Programming Basics
Who wants to talk to me about UCOS system?
I just learned UCOS system by myself, and I still don't understand queues and semaphores. When creating a semaphore, the parameter given is 0. And the subsequent tasks can add to its quantity until it...
大家都是好朋友 Real-time operating system RTOS

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 802  847  1169  1296  2821  17  18  24  27  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号