EEWORLDEEWORLDEEWORLD

Part Number

Search

H0505CA2100CHW-W

Description
Fixed Resistor, Thin Film, 0.125W, 210ohm, 40V, 0.25% +/-Tol, -50,50ppm/Cel, 0505,
CategoryPassive components    The resistor   
File Size91KB,1 Pages
ManufacturerState of the Art Inc.
Environmental Compliance
Download Datasheet Parametric View All

H0505CA2100CHW-W Overview

Fixed Resistor, Thin Film, 0.125W, 210ohm, 40V, 0.25% +/-Tol, -50,50ppm/Cel, 0505,

H0505CA2100CHW-W Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid224404485
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL8.15
structureChip
JESD-609 codee4
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.38 mm
Package length1.35 mm
Package formSMT
Package width1.23 mm
method of packingWaffle Pack
Rated power dissipation(P)0.125 W
resistance210 Ω
Resistor typeFIXED RESISTOR
series0505(STD)-THINFILM
size code0505
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceGold (Au)
Tolerance0.25%
Operating Voltage40 V
PROTECTIVE
ENCAPSULANT
0505 Thin Film Chip Resistor
Standard Grade, Wraparound
PERFORMANCE CHARACTERISTICS
Resistance Range(1)
Tolerances (2)
TCR
Thermal Resistance
Maximum Power
Maximum Voltage
5.6
W- 470KW
0.1%, 0.25%, 0.5%,1%, 2%, 5%
±25, ±50, ±100 ppm
38.8°C/W
125 mW
40 Volts
WRAPAROUND
TERMINATIONS
PRECISION
THIN FILM
99.6% ALUMINA
CURRENT NOISE
TEMPERATURE RISE (°C)
POWER DISSIPATION
fiber epoxy board
(1) Minimum resistance range at 0.1% tolerance is 100ohms.
(2) +/- 0.05% limited availability - consult factory
ceramic board
ENVIRONMENTAL PERFORMANCE (3)
Thermal Shock
Low Temperature Operation
Short-time Overload
Resistance to Bonding Exposure
Moisture Resistance
High Temperature Exposure
Life Test
±0.02%
±0.02%
±0.02%
±0.02%
±0.03%
±0.03%
See Chart
POWER DISSIPATION (WATTS)
TYPICAL LIFE TEST PERFORMANCE
POWER DERATING
(3)Typical resistance change, test methods and criteria
per MIL-PRF-55342.
PART NUMBERING
S 0505 C A 1001 F H B - TR
PACKAGING CODE: - TR = Tape/Reel - W = Waffle Carrier (Default packaging is Bulk)
TERMINATION FINISH: B: Sn60 over nickel barrier W: Gold
TEMPERATURE CHARACTERISTIC TCR: E: ±25 ppm H: ±50 ppm K: ±100 ppm
TOLERANCE: B: 01% C: 0.25% D: 0.5% F: 1% G: 2% J: 5%
RESISTANCE VALUE:
Three or Four digits are used, with all leading digits significant. Four digits are used for 1% tolerance or lower; otherwise, three digits are
used. The last digit specifies the number of zeros to add. The letter "R" is used to represent the decimal for fractional ohmic values.
Example: 5R6 is 5.6 ohms.
PRODUCT DESIGNATION: A: Thin film on alumina
TERMINATION TYPE: C: Wraparound termination
SIZE CODE
GRADE: S: Standard Production H: High Reliability (For Screening options, contact the factory)
MECHANICAL
INCHES
MILLIMETERS
.126
MINIMUM
RECOMMENDED
MOUNTING
PADS
(INCHES)
Length
Width
Thickness
Top Term
Bottom Term
Gap
Approx. Weight
.053 (.051 - .059)
.048 (.046 - .054)
.017 (.013 - .023)
.008 (.005 - .015)
.014 (.010 - .020)
.025 (.021 - .029)
0.0028 grams
1.35
1.23
0.38
0.22
0.36
0.64
(1.30 - 1.50)
(1.17 - 1.38)
(0.33 - 0.58)
(0.13 - 0.38)
(0.25 - 0.51)
(0.54 - 0.74)
.021
.052
.021
“Specifications subject to change without notice.”
STATE OF THE ART, INC.
2470 Fox Hill Road, State College, PA 16803-1797
Phone (814) 355-8004
www.resistor.com
Fax (814) 355-2714
Toll Free 1-800-458-3401
02/08/08
LM3S811 development board does not run normally after restart
I am a novice in ARM. I found an EK-LM3S811 development board (black cutout version) in the company. I plan to use it to make a timing control relay program for testing. I used the source code in the ...
hcyang1422 Microcontroller MCU
Communication frequency of PLC serial communication module
If a PLC serial communication module is used, the baud rate can reach 19200. I communicate 10Bytes each time, so is the communication frequency simply 19200/8/10=240Hz? I use Siemens CPU312 and the se...
chenyi9258 Embedded System
About the method of drawing serpentine difference lines
[i=s]This post was last edited by chen468859 on 2017-2-27 15:32[/i] Draw a serpentine differential line similar to Figure 1 Figure 1 The first step is to set up the differential pair. I drew a schemat...
chen468859 PCB Design
[Hua Diao Experience] 02 Simple use of Xingkong board
[i=s]This post was last edited by eagler8 on 2022-6-14 05:29[/i]When I woke up in the morning, while watching Wangzai’s father’s video, I accidentally learned that the main control chip of the Xingkon...
eagler8 MicroPython Open Source section
Play games and experience Easy Power
The game is a bit simple:lol. But the power module is indeed becoming more and more important in system design. There is a lot of information about Yi Power Supply in the forum. I will take a good loo...
astwyg Analogue and Mixed Signal
The confusion of making single chip microcomputer
I majored in computer science, and it has been 3 years since I graduated. When I was in school, I played with single-chip microcomputers and had some knowledge of hardware, and I drew simple double-si...
bob_zerone Talking about work

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1692  2132  2795  815  1637  35  43  57  17  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号