Package consisting of a FR4 substrate and a Ryton-R4 cover.
Environmental Characteristics
Shock
500 G’s 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D.
Sinusoidal Vibration 0.06” D.A. or 10G’s Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A.
Random Vibration 5.35 G’s rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis.
Moisture
10 cycles, 95% RH, Per MIL-STD-202G, Method 112.
Marking Permanency Per MIL-STD-202G, Method 215J.
Solder Process RoHS compliant, lead free. See solder profile on page 3.
Notes:
1 Frequency stability vs. change in temperature. [±(Fmax - Fmin)/2.Fo].
2 Initial calibration @ 25°C. For OCVCXO control voltage must be fixed.
3 After 30 days of operation
4. Inclusive of calibration @ 25°C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), shock and vibration and 20 years aging
5 Positive slope. (Frequency increases as Vc voltage increases.)
6 Referenced to Fo.
7 Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to
this OCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have
a graduated effect on the stability of approximately 20 ppb per pF load difference.
#define __IO_REG32_BIT(NAME, ADDRESS, ATTRIBUTE, BIT_STRUCT)\ volatile __no_init ATTRIBUTE union \ { \ unsigned long NAME; \ BIT_STRUCT NAME ## _bit; \ } @ ADDRESS I don’t understand the program above...
Today, I was asked in the interview, what should I say about heat dissipation and power consumption? What are the hazards of asymmetric half-bridge when the upper and lower tubes are fully turned on? ...
I use TIM2 to set the timer to one second, but no matter I set TIM_ARRPreloadConfig to DISABLE or ENABLE, the result remains unchanged. I don't understand what TIM_ARRPreloadConfig does. In addition, ...
Preliminary Analysis of Android Multimedia FrameworkZT Zou Dewen Overall Architecture of Android System: Let's first look at the position of the multimedia framework in the entire Android systemFrom t...
I have been using FC18 before, and there were no problems with it, but it took up too many resources, so I changed to FC12. But now I have discovered some problems with FC12. 1. When using FC12 to com...
Some netizens on the forum may have Broadlink smart sockets, which are 220V power sockets that can be remotely controlled by mobile phones. Smart sockets support wifi. The question now is that it is e...
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
Today's security industry has entered the era of massive networking. Many enterprises, especially financial institutions, have established multi-level video surveillance networking platforms. Lever...[Details]
White light LEDs are voltage-sensitive devices. In actual operation, their upper limit is 20mA. However, the current often increases due to various reasons during use. If no protective measures are...[Details]
According to foreign media reports, researchers at the University of Surrey have developed an artificial intelligence system that can accurately locate the location of equipment in densely populate...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
The Automotive Testing and Quality Assurance Expo (ATE 2025) will open on August 27th. At the expo, Rohde & Schwarz (R&S) will showcase six automotive testing solutions, themed "Intelligently Drivi...[Details]
The automotive industry in 2025 is undergoing a thorough intelligent reshuffle.
Geely wants to make changes in the field of AI cockpits: in the future, there will be no traditional smart...[Details]
As AI accelerates across industries, the demand for data center infrastructure is also growing rapidly.
Keysight Technologies, in collaboration with Heavy Reading, released the "Beyo...[Details]
The complexity of the integrated circuits (ICs) used in electronic systems in vehicles is increasing. They aim to execute artificial intelligence (AI) algorithms to control autonomous driving funct...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
HTTP is the abbreviation of Hypertext Transfer Protocol. It is an application protocol based on TCP/IP communication protocol used to transmit HTML and image files. It is an application-level objec...[Details]
The range of an electric vehicle is crucial to the driving experience, and range anxiety is a common headache when driving an electric vehicle. Although the latest electric vehicles can achieve a r...[Details]
Real-time operating system RTOS
京公网安备 11010802033920号
EEWORLD
