EEWORLDEEWORLDEEWORLD

Part Number

Search

355-2-009-1-F-RT0-0980

Description
Board Connector, 9 Contact(s), 1 Row(s), Male, Straight, 0.039 inch Pitch, Surface Mount Terminal
CategoryThe connector    The connector   
File Size1001KB,1 Pages
ManufacturerMPE-Garry GmbH
Download Datasheet Parametric View All

355-2-009-1-F-RT0-0980 Overview

Board Connector, 9 Contact(s), 1 Row(s), Male, Straight, 0.039 inch Pitch, Surface Mount Terminal

355-2-009-1-F-RT0-0980 Parametric

Parameter NameAttribute value
Objectid309013859
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsPEG
body width0.049 inch
subject depth0.15 inch
body length0.354 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage350VAC V
insulator materialTHERMOPLASTIC
Manufacturer's serial number355
Plug contact pitch0.039 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternSTAGGERED
PCB contact row spacing4.3942 mm
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.0066 mm
Termination typeSURFACE MOUNT
Total number of contacts9
Pin Header SMD Sandwich 1,00 mm
Rated current
1,0 A
Rated voltage
50 V
RMS
/ V
DC
Withstand voltage
250 V
RMS
for one minute
Material contact
Copper alloy
Material insulator
High temp. thermoplast UL94V-0
Operating temperature -40°C to +105°C
Max. processing temper. 260°C for 10 seconds
All dimensions in mm.
Series
355
pitch
termination
contact
size
1,00
MPE-Garry GmbH • Schäfflerstraße 13 • 87629 Füssen • Germany • Phone: +49 (0) 83 62 / 91 56-0 • Fax: +49 (0) 83 62 / 91 56-500 • Email: vk@mpe-connector.de • www.mpe-connector.de
Variation
Layout A
n x 1,00
PIN 1
1,25
L
A
B
PCB Layout
050 / 100
max.
pincount
0,30
Product
group
3
(n-1) x 1,00
1,00
1,00
0,30
(n-1) x 1,00
3,10
1,00
1,00
0,56
Layout B
n x 1,00
1,25
L
A
B
(n-1) x 1,00
1,00
1,00
PIN 1
1,00
0,30
(n-1) x 1,00
1,00
0,56
(n/2) x 1,00
L
A
B
(n/2-1) x 1,00
1,00
3,17
1,00
ø0,70
1,00
0,30
(n/2-1) x 1,00
1,00
2,85
1,00
1,00
0,56
A
8,70
9,80
** Positioning peg
0 = Without peg
1 = With peg
Packaging:
R = Reel
T = Tube
Cap:
0 = Without
1 = With
No. of contacts *
(003,... - 100)
Variation (1,2,3)
B
6,00
6,00
Positioning peg**(0,1)
C
6,50
6,50
Plating contact (T,F,S)
L
2,70
3,80
1 2 3
1 2 3
A (1/100 mm)
* No. of contacts:
Variation 1 = 003 - 050
Variation 2 = 003 - 050
Variation 3 = 004 - 100
Plating:
T = Sn
F = Au
S = Selective Au
Packaging (R,T)
Cap (0,1)
(optional only for variation 3)
e.g. 1000 = 10,00 mm
available in variation
see figure left
see figure left
see figure left
see figure left
www.mpe-connector.de
Order code:
Mating series
see page
355-?-???-?-?-R??-????
306
4-4
C+1,00
3
C
ø0,85
C+1,00
2
C
3,10
C+1,00
1
C
3-7
PFC circuit of ucc28019
In this circuit, replacing the resistor with a potentiometer should be able to adjust the output voltage, right? Why is there no response when I adjust it? The input is 24V, and the output is constant...
夜微微凉 Power technology
Practical settings for ISE to call modelsim for simulation
ISE10.1 and ModelSim6.2b were installed. ISE was installed first, and then ModelSim. I tried several methods but failed to connect. Finally, I used the following method to make ISE able to call ModelS...
eeleader FPGA/CPLD
Why does CCS need to install a driver?
CCS is an open software platform that can support different hardware interfaces, so different hardware interfaces must be connected to CCS through standard drivers. Common problems with driver install...
bolibo123 DSP and ARM Processors
Helio Cyclone V SoC Development Board Application FPGA Getting Started Experience
I would like to share my experience of using the Helio demo board with you. Welcome to ask questions and exchange ideas! Please see the attachment for details. Thank you! wu_zhjun 2015-05-29...
wu_zhjun FPGA/CPLD
Learning Board Tutorial Lesson 4 - Timer
Some basic knowledge and demonstrations of timers, welcome to download, thank you!...
764workshop Integrated technical exchanges
Can the PA3 pin of STM32 be used as PWM output of TIM2?
rt,in this post, the moderator said that CH4 of TIM2 cannot be used for PWM input,https://bbs.eeworld.com.cn/icview-109870-1-1.htmlCan it be used for output? I want to set CH4 of TIM2 as PWM output an...
dld2 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1261  588  1983  2812  1236  26  12  40  57  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号