Does anyone want to join the Gangwan embedded training? If yes, please contact QQ568689807. I have carefully compared them and found Gangwan is OK. It is cheap and similar in all aspects. They said th...
[font=Tahoma,]Recently I used DHt11 to measure temperature and humidity, and the results were displayed on 1602. The display of 1602 looked fine, but [/font] [font=Tahoma,]the last 8 digits of the res...
After downloading Windows Embedded CE 6.0 USB Camera Driver from microsoft, is there any software that I can use??? I currently don’t have software that can play videos. Can you provide me with a down...
[size=5]Since I haven't learned the pulse width part, but I need to measure the pulse width,[/size] [size=5][size=7][b][font=宋体][size=9.0pt]Pulse width measurement[/size][/font][/b][/size][font=宋体][si...
Here are some of the most common PCB laminate problems and how to identify them. Once you encounter a PCB laminate problem, you should consider adding it to the PCB laminate material specification. [b...
Personal safety is of utmost importance when measuring electronic systems or circuits. You need to fully understand the performance and usage regulations of the measurement equipment you are using. In...
"Originally, there are many people who can design very good
chips
, but the market does not give domestic
chips
the opportunity to iterate, and domestic companies cannot give engine...[Details]
After studying the F4 FSMC method to drive the touch screen for a few days, I have gained some understanding, which are listed below. The unorganized record is only for my own reference in the future...[Details]
In most countries, the military is a fairly large group, and the health of soldiers is particularly important to the combat effectiveness of the army. The US Department of Defense's Advanced Resear...[Details]
This paper proposes a design scheme for an embedded CNC system based on ARM and FPGA. The software and hardware design of the ARM system, the implementation method of hardware fine interpolation ...[Details]
Kevin Jensen ams Semiconductor
Sensors
and lighting expert. Let's learn more about the relevant content with the network communication editor.
Everything is becoming "smart" these ...[Details]
Today I am using the AD function of the stm8s microcontroller. There are ten channels from AN0 to AN9 on the microcontroller. I want to use only three of them, AN5 to AN7. //ADC initialization void A...[Details]
The single-chip microcomputer running light program requires all 32 serial ports to be used, and each serial port has eight LEDs. Question supplement: The 8051 single-chip microcomputer is used, an...[Details]
Title: Use the table lookup method to convert a hexadecimal number into ASCII code. The input parameter is placed in the internal RAM 50H, and the output parameter is in R0. Requirements: Complete th...[Details]
A simple experimental programming question for the microcontroller: write a 3-byte binary addition subroutine. The program entry is: addend 1: 22H, 21H, 20H three bytes, 22H is the highest bit; adden...[Details]
MCU Programming: Find the average value of 8 unsigned numbers. There are 8 unsigned numbers stored in 8 units of the internal RAM starting at 20H. It is required to save their average value in R2. ;-...[Details]
In the 51 single-chip microcomputer's on-chip data memory units 20H and 21H, the data 9 and 2 are stored respectively. Write a program to calculate the difference and product between the two. The d...[Details]
1. SCL is always controlled by the Master. SDA is controlled by the Slave when reading data and by the Master when writing data according to the direction of data transmission. After the 8-bit data i...[Details]
1. Pin: 0 in 1 out Set Status Output status IO register setting DDR×A certain bit is set to 1, and the corresponding bit IO is set to output; PORT×A certain position is 1/0, and t...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
